shailja/fine-tuned-codegen-2B-Verilog
Text Generation
•
Updated
•
320
•
5
text
stringlengths 938
1.05M
|
|---|
//-----------------------------------------------
// This is the simplest form of inferring the
// simple/SRL(16/32)CE in a Xilinx FPGA.
//-----------------------------------------------
`timescale 1ns / 100ps
`default_nettype none
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_protocol_converter_v2_1_b2s_simple_fifo #
(
parameter C_WIDTH = 8,
parameter C_AWIDTH = 4,
parameter C_DEPTH = 16
)
(
input wire clk, // Main System Clock (Sync FIFO)
input wire rst, // FIFO Counter Reset (Clk
input wire wr_en, // FIFO Write Enable (Clk)
input wire rd_en, // FIFO Read Enable (Clk)
input wire [C_WIDTH-1:0] din, // FIFO Data Input (Clk)
output wire [C_WIDTH-1:0] dout, // FIFO Data Output (Clk)
output wire a_full,
output wire full, // FIFO FULL Status (Clk)
output wire a_empty,
output wire empty // FIFO EMPTY Status (Clk)
);
///////////////////////////////////////
// FIFO Local Parameters
///////////////////////////////////////
localparam [C_AWIDTH-1:0] C_EMPTY = ~(0);
localparam [C_AWIDTH-1:0] C_EMPTY_PRE = (0);
localparam [C_AWIDTH-1:0] C_FULL = C_EMPTY-1;
localparam [C_AWIDTH-1:0] C_FULL_PRE = (C_DEPTH < 8) ? C_FULL-1 : C_FULL-(C_DEPTH/8);
///////////////////////////////////////
// FIFO Internal Signals
///////////////////////////////////////
reg [C_WIDTH-1:0] memory [C_DEPTH-1:0];
reg [C_AWIDTH-1:0] cnt_read;
// synthesis attribute MAX_FANOUT of cnt_read is 10;
///////////////////////////////////////
// Main simple FIFO Array
///////////////////////////////////////
always @(posedge clk) begin : BLKSRL
integer i;
if (wr_en) begin
for (i = 0; i < C_DEPTH-1; i = i + 1) begin
memory[i+1] <= memory[i];
end
memory[0] <= din;
end
end
///////////////////////////////////////
// Read Index Counter
// Up/Down Counter
// *** Notice that there is no ***
// *** OVERRUN protection. ***
///////////////////////////////////////
always @(posedge clk) begin
if (rst) cnt_read <= C_EMPTY;
else if ( wr_en & !rd_en) cnt_read <= cnt_read + 1'b1;
else if (!wr_en & rd_en) cnt_read <= cnt_read - 1'b1;
end
///////////////////////////////////////
// Status Flags / Outputs
// These could be registered, but would
// increase logic in order to pre-decode
// FULL/EMPTY status.
///////////////////////////////////////
assign full = (cnt_read == C_FULL);
assign empty = (cnt_read == C_EMPTY);
assign a_full = ((cnt_read >= C_FULL_PRE) && (cnt_read != C_EMPTY));
assign a_empty = (cnt_read == C_EMPTY_PRE);
assign dout = (C_DEPTH == 1) ? memory[0] : memory[cnt_read];
endmodule // axi_protocol_converter_v2_1_b2s_simple_fifo
`default_nettype wire
|
//-----------------------------------------------
// This is the simplest form of inferring the
// simple/SRL(16/32)CE in a Xilinx FPGA.
//-----------------------------------------------
`timescale 1ns / 100ps
`default_nettype none
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_protocol_converter_v2_1_b2s_simple_fifo #
(
parameter C_WIDTH = 8,
parameter C_AWIDTH = 4,
parameter C_DEPTH = 16
)
(
input wire clk, // Main System Clock (Sync FIFO)
input wire rst, // FIFO Counter Reset (Clk
input wire wr_en, // FIFO Write Enable (Clk)
input wire rd_en, // FIFO Read Enable (Clk)
input wire [C_WIDTH-1:0] din, // FIFO Data Input (Clk)
output wire [C_WIDTH-1:0] dout, // FIFO Data Output (Clk)
output wire a_full,
output wire full, // FIFO FULL Status (Clk)
output wire a_empty,
output wire empty // FIFO EMPTY Status (Clk)
);
///////////////////////////////////////
// FIFO Local Parameters
///////////////////////////////////////
localparam [C_AWIDTH-1:0] C_EMPTY = ~(0);
localparam [C_AWIDTH-1:0] C_EMPTY_PRE = (0);
localparam [C_AWIDTH-1:0] C_FULL = C_EMPTY-1;
localparam [C_AWIDTH-1:0] C_FULL_PRE = (C_DEPTH < 8) ? C_FULL-1 : C_FULL-(C_DEPTH/8);
///////////////////////////////////////
// FIFO Internal Signals
///////////////////////////////////////
reg [C_WIDTH-1:0] memory [C_DEPTH-1:0];
reg [C_AWIDTH-1:0] cnt_read;
// synthesis attribute MAX_FANOUT of cnt_read is 10;
///////////////////////////////////////
// Main simple FIFO Array
///////////////////////////////////////
always @(posedge clk) begin : BLKSRL
integer i;
if (wr_en) begin
for (i = 0; i < C_DEPTH-1; i = i + 1) begin
memory[i+1] <= memory[i];
end
memory[0] <= din;
end
end
///////////////////////////////////////
// Read Index Counter
// Up/Down Counter
// *** Notice that there is no ***
// *** OVERRUN protection. ***
///////////////////////////////////////
always @(posedge clk) begin
if (rst) cnt_read <= C_EMPTY;
else if ( wr_en & !rd_en) cnt_read <= cnt_read + 1'b1;
else if (!wr_en & rd_en) cnt_read <= cnt_read - 1'b1;
end
///////////////////////////////////////
// Status Flags / Outputs
// These could be registered, but would
// increase logic in order to pre-decode
// FULL/EMPTY status.
///////////////////////////////////////
assign full = (cnt_read == C_FULL);
assign empty = (cnt_read == C_EMPTY);
assign a_full = ((cnt_read >= C_FULL_PRE) && (cnt_read != C_EMPTY));
assign a_empty = (cnt_read == C_EMPTY_PRE);
assign dout = (C_DEPTH == 1) ? memory[0] : memory[cnt_read];
endmodule // axi_protocol_converter_v2_1_b2s_simple_fifo
`default_nettype wire
|
//-----------------------------------------------
// This is the simplest form of inferring the
// simple/SRL(16/32)CE in a Xilinx FPGA.
//-----------------------------------------------
`timescale 1ns / 100ps
`default_nettype none
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_protocol_converter_v2_1_b2s_simple_fifo #
(
parameter C_WIDTH = 8,
parameter C_AWIDTH = 4,
parameter C_DEPTH = 16
)
(
input wire clk, // Main System Clock (Sync FIFO)
input wire rst, // FIFO Counter Reset (Clk
input wire wr_en, // FIFO Write Enable (Clk)
input wire rd_en, // FIFO Read Enable (Clk)
input wire [C_WIDTH-1:0] din, // FIFO Data Input (Clk)
output wire [C_WIDTH-1:0] dout, // FIFO Data Output (Clk)
output wire a_full,
output wire full, // FIFO FULL Status (Clk)
output wire a_empty,
output wire empty // FIFO EMPTY Status (Clk)
);
///////////////////////////////////////
// FIFO Local Parameters
///////////////////////////////////////
localparam [C_AWIDTH-1:0] C_EMPTY = ~(0);
localparam [C_AWIDTH-1:0] C_EMPTY_PRE = (0);
localparam [C_AWIDTH-1:0] C_FULL = C_EMPTY-1;
localparam [C_AWIDTH-1:0] C_FULL_PRE = (C_DEPTH < 8) ? C_FULL-1 : C_FULL-(C_DEPTH/8);
///////////////////////////////////////
// FIFO Internal Signals
///////////////////////////////////////
reg [C_WIDTH-1:0] memory [C_DEPTH-1:0];
reg [C_AWIDTH-1:0] cnt_read;
// synthesis attribute MAX_FANOUT of cnt_read is 10;
///////////////////////////////////////
// Main simple FIFO Array
///////////////////////////////////////
always @(posedge clk) begin : BLKSRL
integer i;
if (wr_en) begin
for (i = 0; i < C_DEPTH-1; i = i + 1) begin
memory[i+1] <= memory[i];
end
memory[0] <= din;
end
end
///////////////////////////////////////
// Read Index Counter
// Up/Down Counter
// *** Notice that there is no ***
// *** OVERRUN protection. ***
///////////////////////////////////////
always @(posedge clk) begin
if (rst) cnt_read <= C_EMPTY;
else if ( wr_en & !rd_en) cnt_read <= cnt_read + 1'b1;
else if (!wr_en & rd_en) cnt_read <= cnt_read - 1'b1;
end
///////////////////////////////////////
// Status Flags / Outputs
// These could be registered, but would
// increase logic in order to pre-decode
// FULL/EMPTY status.
///////////////////////////////////////
assign full = (cnt_read == C_FULL);
assign empty = (cnt_read == C_EMPTY);
assign a_full = ((cnt_read >= C_FULL_PRE) && (cnt_read != C_EMPTY));
assign a_empty = (cnt_read == C_EMPTY_PRE);
assign dout = (C_DEPTH == 1) ? memory[0] : memory[cnt_read];
endmodule // axi_protocol_converter_v2_1_b2s_simple_fifo
`default_nettype wire
|
//-----------------------------------------------
// This is the simplest form of inferring the
// simple/SRL(16/32)CE in a Xilinx FPGA.
//-----------------------------------------------
`timescale 1ns / 100ps
`default_nettype none
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_protocol_converter_v2_1_b2s_simple_fifo #
(
parameter C_WIDTH = 8,
parameter C_AWIDTH = 4,
parameter C_DEPTH = 16
)
(
input wire clk, // Main System Clock (Sync FIFO)
input wire rst, // FIFO Counter Reset (Clk
input wire wr_en, // FIFO Write Enable (Clk)
input wire rd_en, // FIFO Read Enable (Clk)
input wire [C_WIDTH-1:0] din, // FIFO Data Input (Clk)
output wire [C_WIDTH-1:0] dout, // FIFO Data Output (Clk)
output wire a_full,
output wire full, // FIFO FULL Status (Clk)
output wire a_empty,
output wire empty // FIFO EMPTY Status (Clk)
);
///////////////////////////////////////
// FIFO Local Parameters
///////////////////////////////////////
localparam [C_AWIDTH-1:0] C_EMPTY = ~(0);
localparam [C_AWIDTH-1:0] C_EMPTY_PRE = (0);
localparam [C_AWIDTH-1:0] C_FULL = C_EMPTY-1;
localparam [C_AWIDTH-1:0] C_FULL_PRE = (C_DEPTH < 8) ? C_FULL-1 : C_FULL-(C_DEPTH/8);
///////////////////////////////////////
// FIFO Internal Signals
///////////////////////////////////////
reg [C_WIDTH-1:0] memory [C_DEPTH-1:0];
reg [C_AWIDTH-1:0] cnt_read;
// synthesis attribute MAX_FANOUT of cnt_read is 10;
///////////////////////////////////////
// Main simple FIFO Array
///////////////////////////////////////
always @(posedge clk) begin : BLKSRL
integer i;
if (wr_en) begin
for (i = 0; i < C_DEPTH-1; i = i + 1) begin
memory[i+1] <= memory[i];
end
memory[0] <= din;
end
end
///////////////////////////////////////
// Read Index Counter
// Up/Down Counter
// *** Notice that there is no ***
// *** OVERRUN protection. ***
///////////////////////////////////////
always @(posedge clk) begin
if (rst) cnt_read <= C_EMPTY;
else if ( wr_en & !rd_en) cnt_read <= cnt_read + 1'b1;
else if (!wr_en & rd_en) cnt_read <= cnt_read - 1'b1;
end
///////////////////////////////////////
// Status Flags / Outputs
// These could be registered, but would
// increase logic in order to pre-decode
// FULL/EMPTY status.
///////////////////////////////////////
assign full = (cnt_read == C_FULL);
assign empty = (cnt_read == C_EMPTY);
assign a_full = ((cnt_read >= C_FULL_PRE) && (cnt_read != C_EMPTY));
assign a_empty = (cnt_read == C_EMPTY_PRE);
assign dout = (C_DEPTH == 1) ? memory[0] : memory[cnt_read];
endmodule // axi_protocol_converter_v2_1_b2s_simple_fifo
`default_nettype wire
|
/*
*
* Copyright (c) 2011 [email protected]
*
*
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
`timescale 1ns/1ps
// A quick define to help index 32-bit words inside a larger register.
`define IDX(x) (((x)+1)*(32)-1):((x)*(32))
// Perform a SHA-256 transformation on the given 512-bit data, and 256-bit
// initial state,
// Outputs one 256-bit hash every LOOP cycle(s).
//
// The LOOP parameter determines both the size and speed of this module.
// A value of 1 implies a fully unrolled SHA-256 calculation spanning 64 round
// modules and calculating a full SHA-256 hash every clock cycle. A value of
// 2 implies a half-unrolled loop, with 32 round modules and calculating
// a full hash in 2 clock cycles. And so forth.
module sha256_transform #(
parameter LOOP = 7'd64 // For ltcminer
) (
input clk,
input feedback,
input [5:0] cnt,
input [255:0] rx_state,
input [511:0] rx_input,
output reg [255:0] tx_hash
);
// Constants defined by the SHA-2 standard.
localparam Ks = {
32'h428a2f98, 32'h71374491, 32'hb5c0fbcf, 32'he9b5dba5,
32'h3956c25b, 32'h59f111f1, 32'h923f82a4, 32'hab1c5ed5,
32'hd807aa98, 32'h12835b01, 32'h243185be, 32'h550c7dc3,
32'h72be5d74, 32'h80deb1fe, 32'h9bdc06a7, 32'hc19bf174,
32'he49b69c1, 32'hefbe4786, 32'h0fc19dc6, 32'h240ca1cc,
32'h2de92c6f, 32'h4a7484aa, 32'h5cb0a9dc, 32'h76f988da,
32'h983e5152, 32'ha831c66d, 32'hb00327c8, 32'hbf597fc7,
32'hc6e00bf3, 32'hd5a79147, 32'h06ca6351, 32'h14292967,
32'h27b70a85, 32'h2e1b2138, 32'h4d2c6dfc, 32'h53380d13,
32'h650a7354, 32'h766a0abb, 32'h81c2c92e, 32'h92722c85,
32'ha2bfe8a1, 32'ha81a664b, 32'hc24b8b70, 32'hc76c51a3,
32'hd192e819, 32'hd6990624, 32'hf40e3585, 32'h106aa070,
32'h19a4c116, 32'h1e376c08, 32'h2748774c, 32'h34b0bcb5,
32'h391c0cb3, 32'h4ed8aa4a, 32'h5b9cca4f, 32'h682e6ff3,
32'h748f82ee, 32'h78a5636f, 32'h84c87814, 32'h8cc70208,
32'h90befffa, 32'ha4506ceb, 32'hbef9a3f7, 32'hc67178f2};
genvar i;
generate
for (i = 0; i < 64/LOOP; i = i + 1) begin : HASHERS
// These are declared as registers in sha256_digester
wire [511:0] W; // reg tx_w
wire [255:0] state; // reg tx_state
if(i == 0)
sha256_digester U (
.clk(clk),
.k(Ks[32*(63-cnt) +: 32]),
.rx_w(feedback ? W : rx_input),
.rx_state(feedback ? state : rx_state),
.tx_w(W),
.tx_state(state)
);
else
sha256_digester U (
.clk(clk),
.k(Ks[32*(63-LOOP*i-cnt) +: 32]),
.rx_w(feedback ? W : HASHERS[i-1].W),
.rx_state(feedback ? state : HASHERS[i-1].state),
.tx_w(W),
.tx_state(state)
);
end
endgenerate
always @ (posedge clk)
begin
if (!feedback)
begin
tx_hash[`IDX(0)] <= rx_state[`IDX(0)] + HASHERS[64/LOOP-6'd1].state[`IDX(0)];
tx_hash[`IDX(1)] <= rx_state[`IDX(1)] + HASHERS[64/LOOP-6'd1].state[`IDX(1)];
tx_hash[`IDX(2)] <= rx_state[`IDX(2)] + HASHERS[64/LOOP-6'd1].state[`IDX(2)];
tx_hash[`IDX(3)] <= rx_state[`IDX(3)] + HASHERS[64/LOOP-6'd1].state[`IDX(3)];
tx_hash[`IDX(4)] <= rx_state[`IDX(4)] + HASHERS[64/LOOP-6'd1].state[`IDX(4)];
tx_hash[`IDX(5)] <= rx_state[`IDX(5)] + HASHERS[64/LOOP-6'd1].state[`IDX(5)];
tx_hash[`IDX(6)] <= rx_state[`IDX(6)] + HASHERS[64/LOOP-6'd1].state[`IDX(6)];
tx_hash[`IDX(7)] <= rx_state[`IDX(7)] + HASHERS[64/LOOP-6'd1].state[`IDX(7)];
end
end
endmodule
module sha256_digester (clk, k, rx_w, rx_state, tx_w, tx_state);
input clk;
input [31:0] k;
input [511:0] rx_w;
input [255:0] rx_state;
output reg [511:0] tx_w;
output reg [255:0] tx_state;
wire [31:0] e0_w, e1_w, ch_w, maj_w, s0_w, s1_w;
e0 e0_blk (rx_state[`IDX(0)], e0_w);
e1 e1_blk (rx_state[`IDX(4)], e1_w);
ch ch_blk (rx_state[`IDX(4)], rx_state[`IDX(5)], rx_state[`IDX(6)], ch_w);
maj maj_blk (rx_state[`IDX(0)], rx_state[`IDX(1)], rx_state[`IDX(2)], maj_w);
s0 s0_blk (rx_w[63:32], s0_w);
s1 s1_blk (rx_w[479:448], s1_w);
wire [31:0] t1 = rx_state[`IDX(7)] + e1_w + ch_w + rx_w[31:0] + k;
wire [31:0] t2 = e0_w + maj_w;
wire [31:0] new_w = s1_w + rx_w[319:288] + s0_w + rx_w[31:0];
always @ (posedge clk)
begin
tx_w[511:480] <= new_w;
tx_w[479:0] <= rx_w[511:32];
tx_state[`IDX(7)] <= rx_state[`IDX(6)];
tx_state[`IDX(6)] <= rx_state[`IDX(5)];
tx_state[`IDX(5)] <= rx_state[`IDX(4)];
tx_state[`IDX(4)] <= rx_state[`IDX(3)] + t1;
tx_state[`IDX(3)] <= rx_state[`IDX(2)];
tx_state[`IDX(2)] <= rx_state[`IDX(1)];
tx_state[`IDX(1)] <= rx_state[`IDX(0)];
tx_state[`IDX(0)] <= t1 + t2;
end
endmodule
|
/*
*
* Copyright (c) 2011 [email protected]
*
*
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
`timescale 1ns/1ps
// A quick define to help index 32-bit words inside a larger register.
`define IDX(x) (((x)+1)*(32)-1):((x)*(32))
// Perform a SHA-256 transformation on the given 512-bit data, and 256-bit
// initial state,
// Outputs one 256-bit hash every LOOP cycle(s).
//
// The LOOP parameter determines both the size and speed of this module.
// A value of 1 implies a fully unrolled SHA-256 calculation spanning 64 round
// modules and calculating a full SHA-256 hash every clock cycle. A value of
// 2 implies a half-unrolled loop, with 32 round modules and calculating
// a full hash in 2 clock cycles. And so forth.
module sha256_transform #(
parameter LOOP = 7'd64 // For ltcminer
) (
input clk,
input feedback,
input [5:0] cnt,
input [255:0] rx_state,
input [511:0] rx_input,
output reg [255:0] tx_hash
);
// Constants defined by the SHA-2 standard.
localparam Ks = {
32'h428a2f98, 32'h71374491, 32'hb5c0fbcf, 32'he9b5dba5,
32'h3956c25b, 32'h59f111f1, 32'h923f82a4, 32'hab1c5ed5,
32'hd807aa98, 32'h12835b01, 32'h243185be, 32'h550c7dc3,
32'h72be5d74, 32'h80deb1fe, 32'h9bdc06a7, 32'hc19bf174,
32'he49b69c1, 32'hefbe4786, 32'h0fc19dc6, 32'h240ca1cc,
32'h2de92c6f, 32'h4a7484aa, 32'h5cb0a9dc, 32'h76f988da,
32'h983e5152, 32'ha831c66d, 32'hb00327c8, 32'hbf597fc7,
32'hc6e00bf3, 32'hd5a79147, 32'h06ca6351, 32'h14292967,
32'h27b70a85, 32'h2e1b2138, 32'h4d2c6dfc, 32'h53380d13,
32'h650a7354, 32'h766a0abb, 32'h81c2c92e, 32'h92722c85,
32'ha2bfe8a1, 32'ha81a664b, 32'hc24b8b70, 32'hc76c51a3,
32'hd192e819, 32'hd6990624, 32'hf40e3585, 32'h106aa070,
32'h19a4c116, 32'h1e376c08, 32'h2748774c, 32'h34b0bcb5,
32'h391c0cb3, 32'h4ed8aa4a, 32'h5b9cca4f, 32'h682e6ff3,
32'h748f82ee, 32'h78a5636f, 32'h84c87814, 32'h8cc70208,
32'h90befffa, 32'ha4506ceb, 32'hbef9a3f7, 32'hc67178f2};
genvar i;
generate
for (i = 0; i < 64/LOOP; i = i + 1) begin : HASHERS
// These are declared as registers in sha256_digester
wire [511:0] W; // reg tx_w
wire [255:0] state; // reg tx_state
if(i == 0)
sha256_digester U (
.clk(clk),
.k(Ks[32*(63-cnt) +: 32]),
.rx_w(feedback ? W : rx_input),
.rx_state(feedback ? state : rx_state),
.tx_w(W),
.tx_state(state)
);
else
sha256_digester U (
.clk(clk),
.k(Ks[32*(63-LOOP*i-cnt) +: 32]),
.rx_w(feedback ? W : HASHERS[i-1].W),
.rx_state(feedback ? state : HASHERS[i-1].state),
.tx_w(W),
.tx_state(state)
);
end
endgenerate
always @ (posedge clk)
begin
if (!feedback)
begin
tx_hash[`IDX(0)] <= rx_state[`IDX(0)] + HASHERS[64/LOOP-6'd1].state[`IDX(0)];
tx_hash[`IDX(1)] <= rx_state[`IDX(1)] + HASHERS[64/LOOP-6'd1].state[`IDX(1)];
tx_hash[`IDX(2)] <= rx_state[`IDX(2)] + HASHERS[64/LOOP-6'd1].state[`IDX(2)];
tx_hash[`IDX(3)] <= rx_state[`IDX(3)] + HASHERS[64/LOOP-6'd1].state[`IDX(3)];
tx_hash[`IDX(4)] <= rx_state[`IDX(4)] + HASHERS[64/LOOP-6'd1].state[`IDX(4)];
tx_hash[`IDX(5)] <= rx_state[`IDX(5)] + HASHERS[64/LOOP-6'd1].state[`IDX(5)];
tx_hash[`IDX(6)] <= rx_state[`IDX(6)] + HASHERS[64/LOOP-6'd1].state[`IDX(6)];
tx_hash[`IDX(7)] <= rx_state[`IDX(7)] + HASHERS[64/LOOP-6'd1].state[`IDX(7)];
end
end
endmodule
module sha256_digester (clk, k, rx_w, rx_state, tx_w, tx_state);
input clk;
input [31:0] k;
input [511:0] rx_w;
input [255:0] rx_state;
output reg [511:0] tx_w;
output reg [255:0] tx_state;
wire [31:0] e0_w, e1_w, ch_w, maj_w, s0_w, s1_w;
e0 e0_blk (rx_state[`IDX(0)], e0_w);
e1 e1_blk (rx_state[`IDX(4)], e1_w);
ch ch_blk (rx_state[`IDX(4)], rx_state[`IDX(5)], rx_state[`IDX(6)], ch_w);
maj maj_blk (rx_state[`IDX(0)], rx_state[`IDX(1)], rx_state[`IDX(2)], maj_w);
s0 s0_blk (rx_w[63:32], s0_w);
s1 s1_blk (rx_w[479:448], s1_w);
wire [31:0] t1 = rx_state[`IDX(7)] + e1_w + ch_w + rx_w[31:0] + k;
wire [31:0] t2 = e0_w + maj_w;
wire [31:0] new_w = s1_w + rx_w[319:288] + s0_w + rx_w[31:0];
always @ (posedge clk)
begin
tx_w[511:480] <= new_w;
tx_w[479:0] <= rx_w[511:32];
tx_state[`IDX(7)] <= rx_state[`IDX(6)];
tx_state[`IDX(6)] <= rx_state[`IDX(5)];
tx_state[`IDX(5)] <= rx_state[`IDX(4)];
tx_state[`IDX(4)] <= rx_state[`IDX(3)] + t1;
tx_state[`IDX(3)] <= rx_state[`IDX(2)];
tx_state[`IDX(2)] <= rx_state[`IDX(1)];
tx_state[`IDX(1)] <= rx_state[`IDX(0)];
tx_state[`IDX(0)] <= t1 + t2;
end
endmodule
|
/*
*
* Copyright (c) 2011 [email protected]
*
*
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
`timescale 1ns/1ps
// A quick define to help index 32-bit words inside a larger register.
`define IDX(x) (((x)+1)*(32)-1):((x)*(32))
// Perform a SHA-256 transformation on the given 512-bit data, and 256-bit
// initial state,
// Outputs one 256-bit hash every LOOP cycle(s).
//
// The LOOP parameter determines both the size and speed of this module.
// A value of 1 implies a fully unrolled SHA-256 calculation spanning 64 round
// modules and calculating a full SHA-256 hash every clock cycle. A value of
// 2 implies a half-unrolled loop, with 32 round modules and calculating
// a full hash in 2 clock cycles. And so forth.
module sha256_transform #(
parameter LOOP = 7'd64 // For ltcminer
) (
input clk,
input feedback,
input [5:0] cnt,
input [255:0] rx_state,
input [511:0] rx_input,
output reg [255:0] tx_hash
);
// Constants defined by the SHA-2 standard.
localparam Ks = {
32'h428a2f98, 32'h71374491, 32'hb5c0fbcf, 32'he9b5dba5,
32'h3956c25b, 32'h59f111f1, 32'h923f82a4, 32'hab1c5ed5,
32'hd807aa98, 32'h12835b01, 32'h243185be, 32'h550c7dc3,
32'h72be5d74, 32'h80deb1fe, 32'h9bdc06a7, 32'hc19bf174,
32'he49b69c1, 32'hefbe4786, 32'h0fc19dc6, 32'h240ca1cc,
32'h2de92c6f, 32'h4a7484aa, 32'h5cb0a9dc, 32'h76f988da,
32'h983e5152, 32'ha831c66d, 32'hb00327c8, 32'hbf597fc7,
32'hc6e00bf3, 32'hd5a79147, 32'h06ca6351, 32'h14292967,
32'h27b70a85, 32'h2e1b2138, 32'h4d2c6dfc, 32'h53380d13,
32'h650a7354, 32'h766a0abb, 32'h81c2c92e, 32'h92722c85,
32'ha2bfe8a1, 32'ha81a664b, 32'hc24b8b70, 32'hc76c51a3,
32'hd192e819, 32'hd6990624, 32'hf40e3585, 32'h106aa070,
32'h19a4c116, 32'h1e376c08, 32'h2748774c, 32'h34b0bcb5,
32'h391c0cb3, 32'h4ed8aa4a, 32'h5b9cca4f, 32'h682e6ff3,
32'h748f82ee, 32'h78a5636f, 32'h84c87814, 32'h8cc70208,
32'h90befffa, 32'ha4506ceb, 32'hbef9a3f7, 32'hc67178f2};
genvar i;
generate
for (i = 0; i < 64/LOOP; i = i + 1) begin : HASHERS
// These are declared as registers in sha256_digester
wire [511:0] W; // reg tx_w
wire [255:0] state; // reg tx_state
if(i == 0)
sha256_digester U (
.clk(clk),
.k(Ks[32*(63-cnt) +: 32]),
.rx_w(feedback ? W : rx_input),
.rx_state(feedback ? state : rx_state),
.tx_w(W),
.tx_state(state)
);
else
sha256_digester U (
.clk(clk),
.k(Ks[32*(63-LOOP*i-cnt) +: 32]),
.rx_w(feedback ? W : HASHERS[i-1].W),
.rx_state(feedback ? state : HASHERS[i-1].state),
.tx_w(W),
.tx_state(state)
);
end
endgenerate
always @ (posedge clk)
begin
if (!feedback)
begin
tx_hash[`IDX(0)] <= rx_state[`IDX(0)] + HASHERS[64/LOOP-6'd1].state[`IDX(0)];
tx_hash[`IDX(1)] <= rx_state[`IDX(1)] + HASHERS[64/LOOP-6'd1].state[`IDX(1)];
tx_hash[`IDX(2)] <= rx_state[`IDX(2)] + HASHERS[64/LOOP-6'd1].state[`IDX(2)];
tx_hash[`IDX(3)] <= rx_state[`IDX(3)] + HASHERS[64/LOOP-6'd1].state[`IDX(3)];
tx_hash[`IDX(4)] <= rx_state[`IDX(4)] + HASHERS[64/LOOP-6'd1].state[`IDX(4)];
tx_hash[`IDX(5)] <= rx_state[`IDX(5)] + HASHERS[64/LOOP-6'd1].state[`IDX(5)];
tx_hash[`IDX(6)] <= rx_state[`IDX(6)] + HASHERS[64/LOOP-6'd1].state[`IDX(6)];
tx_hash[`IDX(7)] <= rx_state[`IDX(7)] + HASHERS[64/LOOP-6'd1].state[`IDX(7)];
end
end
endmodule
module sha256_digester (clk, k, rx_w, rx_state, tx_w, tx_state);
input clk;
input [31:0] k;
input [511:0] rx_w;
input [255:0] rx_state;
output reg [511:0] tx_w;
output reg [255:0] tx_state;
wire [31:0] e0_w, e1_w, ch_w, maj_w, s0_w, s1_w;
e0 e0_blk (rx_state[`IDX(0)], e0_w);
e1 e1_blk (rx_state[`IDX(4)], e1_w);
ch ch_blk (rx_state[`IDX(4)], rx_state[`IDX(5)], rx_state[`IDX(6)], ch_w);
maj maj_blk (rx_state[`IDX(0)], rx_state[`IDX(1)], rx_state[`IDX(2)], maj_w);
s0 s0_blk (rx_w[63:32], s0_w);
s1 s1_blk (rx_w[479:448], s1_w);
wire [31:0] t1 = rx_state[`IDX(7)] + e1_w + ch_w + rx_w[31:0] + k;
wire [31:0] t2 = e0_w + maj_w;
wire [31:0] new_w = s1_w + rx_w[319:288] + s0_w + rx_w[31:0];
always @ (posedge clk)
begin
tx_w[511:480] <= new_w;
tx_w[479:0] <= rx_w[511:32];
tx_state[`IDX(7)] <= rx_state[`IDX(6)];
tx_state[`IDX(6)] <= rx_state[`IDX(5)];
tx_state[`IDX(5)] <= rx_state[`IDX(4)];
tx_state[`IDX(4)] <= rx_state[`IDX(3)] + t1;
tx_state[`IDX(3)] <= rx_state[`IDX(2)];
tx_state[`IDX(2)] <= rx_state[`IDX(1)];
tx_state[`IDX(1)] <= rx_state[`IDX(0)];
tx_state[`IDX(0)] <= t1 + t2;
end
endmodule
|
// Taken from http://www.europa.com/~celiac/fsm_samp.html
// These are the symbolic names for states
parameter [1:0] //synopsys enum state_info
S0 = 2'h0,
S1 = 2'h1,
S2 = 2'h2,
S3 = 2'h3;
// These are the current state and next state variables
reg [1:0] /* synopsys enum state_info */ state;
reg [1:0] /* synopsys enum state_info */ next_state;
// synopsys state_vector state
always @ (state or y or x)
begin
next_state = state;
case (state) // synopsys full_case parallel_case
S0: begin
if (x) begin
next_state = S1;
end
else begin
next_state = S2;
end
end
S1: begin
if (y) begin
next_state = S2;
end
else begin
next_state = S0;
end
end
S2: begin
if (x & y) begin
next_state = S3;
end
else begin
next_state = S0;
end
end
S3: begin
next_state = S0;
end
endcase
end
always @ (posedge clk or posedge reset)
begin
if (reset) begin
state <= S0;
end
else begin
state <= next_state;
end
end
|
// Taken from http://www.europa.com/~celiac/fsm_samp.html
// These are the symbolic names for states
parameter [1:0] //synopsys enum state_info
S0 = 2'h0,
S1 = 2'h1,
S2 = 2'h2,
S3 = 2'h3;
// These are the current state and next state variables
reg [1:0] /* synopsys enum state_info */ state;
reg [1:0] /* synopsys enum state_info */ next_state;
// synopsys state_vector state
always @ (state or y or x)
begin
next_state = state;
case (state) // synopsys full_case parallel_case
S0: begin
if (x) begin
next_state = S1;
end
else begin
next_state = S2;
end
end
S1: begin
if (y) begin
next_state = S2;
end
else begin
next_state = S0;
end
end
S2: begin
if (x & y) begin
next_state = S3;
end
else begin
next_state = S0;
end
end
S3: begin
next_state = S0;
end
endcase
end
always @ (posedge clk or posedge reset)
begin
if (reset) begin
state <= S0;
end
else begin
state <= next_state;
end
end
|
// Taken from http://www.europa.com/~celiac/fsm_samp.html
// These are the symbolic names for states
parameter [1:0] //synopsys enum state_info
S0 = 2'h0,
S1 = 2'h1,
S2 = 2'h2,
S3 = 2'h3;
// These are the current state and next state variables
reg [1:0] /* synopsys enum state_info */ state;
reg [1:0] /* synopsys enum state_info */ next_state;
// synopsys state_vector state
always @ (state or y or x)
begin
next_state = state;
case (state) // synopsys full_case parallel_case
S0: begin
if (x) begin
next_state = S1;
end
else begin
next_state = S2;
end
end
S1: begin
if (y) begin
next_state = S2;
end
else begin
next_state = S0;
end
end
S2: begin
if (x & y) begin
next_state = S3;
end
else begin
next_state = S0;
end
end
S3: begin
next_state = S0;
end
endcase
end
always @ (posedge clk or posedge reset)
begin
if (reset) begin
state <= S0;
end
else begin
state <= next_state;
end
end
|
// Taken from http://www.europa.com/~celiac/fsm_samp.html
// These are the symbolic names for states
parameter [1:0] //synopsys enum state_info
S0 = 2'h0,
S1 = 2'h1,
S2 = 2'h2,
S3 = 2'h3;
// These are the current state and next state variables
reg [1:0] /* synopsys enum state_info */ state;
reg [1:0] /* synopsys enum state_info */ next_state;
// synopsys state_vector state
always @ (state or y or x)
begin
next_state = state;
case (state) // synopsys full_case parallel_case
S0: begin
if (x) begin
next_state = S1;
end
else begin
next_state = S2;
end
end
S1: begin
if (y) begin
next_state = S2;
end
else begin
next_state = S0;
end
end
S2: begin
if (x & y) begin
next_state = S3;
end
else begin
next_state = S0;
end
end
S3: begin
next_state = S0;
end
endcase
end
always @ (posedge clk or posedge reset)
begin
if (reset) begin
state <= S0;
end
else begin
state <= next_state;
end
end
|
// Taken from http://www.europa.com/~celiac/fsm_samp.html
// These are the symbolic names for states
parameter [1:0] //synopsys enum state_info
S0 = 2'h0,
S1 = 2'h1,
S2 = 2'h2,
S3 = 2'h3;
// These are the current state and next state variables
reg [1:0] /* synopsys enum state_info */ state;
reg [1:0] /* synopsys enum state_info */ next_state;
// synopsys state_vector state
always @ (state or y or x)
begin
next_state = state;
case (state) // synopsys full_case parallel_case
S0: begin
if (x) begin
next_state = S1;
end
else begin
next_state = S2;
end
end
S1: begin
if (y) begin
next_state = S2;
end
else begin
next_state = S0;
end
end
S2: begin
if (x & y) begin
next_state = S3;
end
else begin
next_state = S0;
end
end
S3: begin
next_state = S0;
end
endcase
end
always @ (posedge clk or posedge reset)
begin
if (reset) begin
state <= S0;
end
else begin
state <= next_state;
end
end
|
// Taken from http://www.europa.com/~celiac/fsm_samp.html
// These are the symbolic names for states
parameter [1:0] //synopsys enum state_info
S0 = 2'h0,
S1 = 2'h1,
S2 = 2'h2,
S3 = 2'h3;
// These are the current state and next state variables
reg [1:0] /* synopsys enum state_info */ state;
reg [1:0] /* synopsys enum state_info */ next_state;
// synopsys state_vector state
always @ (state or y or x)
begin
next_state = state;
case (state) // synopsys full_case parallel_case
S0: begin
if (x) begin
next_state = S1;
end
else begin
next_state = S2;
end
end
S1: begin
if (y) begin
next_state = S2;
end
else begin
next_state = S0;
end
end
S2: begin
if (x & y) begin
next_state = S3;
end
else begin
next_state = S0;
end
end
S3: begin
next_state = S0;
end
endcase
end
always @ (posedge clk or posedge reset)
begin
if (reset) begin
state <= S0;
end
else begin
state <= next_state;
end
end
|
// Taken from http://www.europa.com/~celiac/fsm_samp.html
// These are the symbolic names for states
parameter [1:0] //synopsys enum state_info
S0 = 2'h0,
S1 = 2'h1,
S2 = 2'h2,
S3 = 2'h3;
// These are the current state and next state variables
reg [1:0] /* synopsys enum state_info */ state;
reg [1:0] /* synopsys enum state_info */ next_state;
// synopsys state_vector state
always @ (state or y or x)
begin
next_state = state;
case (state) // synopsys full_case parallel_case
S0: begin
if (x) begin
next_state = S1;
end
else begin
next_state = S2;
end
end
S1: begin
if (y) begin
next_state = S2;
end
else begin
next_state = S0;
end
end
S2: begin
if (x & y) begin
next_state = S3;
end
else begin
next_state = S0;
end
end
S3: begin
next_state = S0;
end
endcase
end
always @ (posedge clk or posedge reset)
begin
if (reset) begin
state <= S0;
end
else begin
state <= next_state;
end
end
|
// Taken from http://www.europa.com/~celiac/fsm_samp.html
// These are the symbolic names for states
parameter [1:0] //synopsys enum state_info
S0 = 2'h0,
S1 = 2'h1,
S2 = 2'h2,
S3 = 2'h3;
// These are the current state and next state variables
reg [1:0] /* synopsys enum state_info */ state;
reg [1:0] /* synopsys enum state_info */ next_state;
// synopsys state_vector state
always @ (state or y or x)
begin
next_state = state;
case (state) // synopsys full_case parallel_case
S0: begin
if (x) begin
next_state = S1;
end
else begin
next_state = S2;
end
end
S1: begin
if (y) begin
next_state = S2;
end
else begin
next_state = S0;
end
end
S2: begin
if (x & y) begin
next_state = S3;
end
else begin
next_state = S0;
end
end
S3: begin
next_state = S0;
end
endcase
end
always @ (posedge clk or posedge reset)
begin
if (reset) begin
state <= S0;
end
else begin
state <= next_state;
end
end
|
`include "hi_simulate.v"
/*
pck0 - input main 24Mhz clock (PLL / 4)
[7:0] adc_d - input data from A/D converter
mod_type - modulation type
pwr_lo - output to coil drivers (ssp_clk / 8)
adc_clk - output A/D clock signal
ssp_frame - output SSS frame indicator (goes high while the 8 bits are shifted)
ssp_din - output SSP data to ARM (shifts 8 bit A/D value serially to ARM MSB first)
ssp_clk - output SSP clock signal
ck_1356meg - input unused
ck_1356megb - input unused
ssp_dout - input unused
cross_hi - input unused
cross_lo - input unused
pwr_hi - output unused, tied low
pwr_oe1 - output unused, undefined
pwr_oe2 - output unused, undefined
pwr_oe3 - output unused, undefined
pwr_oe4 - output unused, undefined
dbg - output alias for adc_clk
*/
module testbed_hi_simulate;
reg pck0;
reg [7:0] adc_d;
reg mod_type;
wire pwr_lo;
wire adc_clk;
reg ck_1356meg;
reg ck_1356megb;
wire ssp_frame;
wire ssp_din;
wire ssp_clk;
reg ssp_dout;
wire pwr_hi;
wire pwr_oe1;
wire pwr_oe2;
wire pwr_oe3;
wire pwr_oe4;
wire cross_lo;
wire cross_hi;
wire dbg;
hi_simulate #(5,200) dut(
.pck0(pck0),
.ck_1356meg(ck_1356meg),
.ck_1356megb(ck_1356megb),
.pwr_lo(pwr_lo),
.pwr_hi(pwr_hi),
.pwr_oe1(pwr_oe1),
.pwr_oe2(pwr_oe2),
.pwr_oe3(pwr_oe3),
.pwr_oe4(pwr_oe4),
.adc_d(adc_d),
.adc_clk(adc_clk),
.ssp_frame(ssp_frame),
.ssp_din(ssp_din),
.ssp_dout(ssp_dout),
.ssp_clk(ssp_clk),
.cross_hi(cross_hi),
.cross_lo(cross_lo),
.dbg(dbg),
.mod_type(mod_type)
);
integer idx, i;
// main clock
always #5 begin
ck_1356megb = !ck_1356megb;
ck_1356meg = ck_1356megb;
end
always begin
@(negedge adc_clk) ;
adc_d = $random;
end
//crank DUT
task crank_dut;
begin
@(negedge ssp_clk) ;
ssp_dout = $random;
end
endtask
initial begin
// init inputs
ck_1356megb = 0;
// random values
adc_d = 0;
ssp_dout=1;
// shallow modulation off
mod_type=0;
for (i = 0 ; i < 16 ; i = i + 1) begin
crank_dut;
end
// shallow modulation on
mod_type=1;
for (i = 0 ; i < 16 ; i = i + 1) begin
crank_dut;
end
$finish;
end
endmodule // main
|
//-----------------------------------------------------------------------------
//-- (c) Copyright 2010 Xilinx, Inc. All rights reserved.
//--
//-- This file contains confidential and proprietary information
//-- of Xilinx, Inc. and is protected under U.S. and
//-- international copyright and other intellectual property
//-- laws.
//--
//-- DISCLAIMER
//-- This disclaimer is not a license and does not grant any
//-- rights to the materials distributed herewith. Except as
//-- otherwise provided in a valid license issued to you by
//-- Xilinx, and to the maximum extent permitted by applicable
//-- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
//-- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
//-- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
//-- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
//-- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
//-- (2) Xilinx shall not be liable (whether in contract or tort,
//-- including negligence, or under any other theory of
//-- liability) for any loss or damage of any kind or nature
//-- related to, arising under or in connection with these
//-- materials, including for any direct, or any indirect,
//-- special, incidental, or consequential loss or damage
//-- (including loss of data, profits, goodwill, or any type of
//-- loss or damage suffered as a result of any action brought
//-- by a third party) even if such damage or loss was
//-- reasonably foreseeable or Xilinx had been advised of the
//-- possibility of the same.
//--
//-- CRITICAL APPLICATIONS
//-- Xilinx products are not designed or intended to be fail-
//-- safe, or for use in any application requiring fail-safe
//-- performance, such as life-support or safety devices or
//-- systems, Class III medical devices, nuclear facilities,
//-- applications related to the deployment of airbags, or any
//-- other applications that could lead to death, personal
//-- injury, or severe property or environmental damage
//-- (individually and collectively, "Critical
//-- Applications"). Customer assumes the sole risk and
//-- liability of any use of Xilinx products in Critical
//-- Applications, subject only to applicable laws and
//-- regulations governing limitations on product liability.
//--
//-- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
//-- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
//
// Description: ACP Transaction Checker
//
// Check for optimized ACP transactions and flag if they are broken.
//
//
//
// Verilog-standard: Verilog 2001
//--------------------------------------------------------------------------
//
// Structure:
// atc
// aw_atc
// w_atc
// b_atc
//
//--------------------------------------------------------------------------
`timescale 1ps/1ps
`default_nettype none
module processing_system7_v5_5_atc #
(
parameter C_FAMILY = "rtl",
// FPGA Family. Current version: virtex6, spartan6 or later.
parameter integer C_AXI_ID_WIDTH = 4,
// Width of all ID signals on SI and MI side of checker.
// Range: >= 1.
parameter integer C_AXI_ADDR_WIDTH = 32,
// Width of all ADDR signals on SI and MI side of checker.
// Range: 32.
parameter integer C_AXI_DATA_WIDTH = 64,
// Width of all DATA signals on SI and MI side of checker.
// Range: 64.
parameter integer C_AXI_AWUSER_WIDTH = 1,
// Width of AWUSER signals.
// Range: >= 1.
parameter integer C_AXI_ARUSER_WIDTH = 1,
// Width of ARUSER signals.
// Range: >= 1.
parameter integer C_AXI_WUSER_WIDTH = 1,
// Width of WUSER signals.
// Range: >= 1.
parameter integer C_AXI_RUSER_WIDTH = 1,
// Width of RUSER signals.
// Range: >= 1.
parameter integer C_AXI_BUSER_WIDTH = 1
// Width of BUSER signals.
// Range: >= 1.
)
(
// Global Signals
input wire ACLK,
input wire ARESETN,
// Slave Interface Write Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_AWADDR,
input wire [4-1:0] S_AXI_AWLEN,
input wire [3-1:0] S_AXI_AWSIZE,
input wire [2-1:0] S_AXI_AWBURST,
input wire [2-1:0] S_AXI_AWLOCK,
input wire [4-1:0] S_AXI_AWCACHE,
input wire [3-1:0] S_AXI_AWPROT,
input wire [C_AXI_AWUSER_WIDTH-1:0] S_AXI_AWUSER,
input wire S_AXI_AWVALID,
output wire S_AXI_AWREADY,
// Slave Interface Write Data Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_WID,
input wire [C_AXI_DATA_WIDTH-1:0] S_AXI_WDATA,
input wire [C_AXI_DATA_WIDTH/8-1:0] S_AXI_WSTRB,
input wire S_AXI_WLAST,
input wire [C_AXI_WUSER_WIDTH-1:0] S_AXI_WUSER,
input wire S_AXI_WVALID,
output wire S_AXI_WREADY,
// Slave Interface Write Response Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID,
output wire [2-1:0] S_AXI_BRESP,
output wire [C_AXI_BUSER_WIDTH-1:0] S_AXI_BUSER,
output wire S_AXI_BVALID,
input wire S_AXI_BREADY,
// Slave Interface Read Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_ARADDR,
input wire [4-1:0] S_AXI_ARLEN,
input wire [3-1:0] S_AXI_ARSIZE,
input wire [2-1:0] S_AXI_ARBURST,
input wire [2-1:0] S_AXI_ARLOCK,
input wire [4-1:0] S_AXI_ARCACHE,
input wire [3-1:0] S_AXI_ARPROT,
input wire [C_AXI_ARUSER_WIDTH-1:0] S_AXI_ARUSER,
input wire S_AXI_ARVALID,
output wire S_AXI_ARREADY,
// Slave Interface Read Data Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID,
output wire [C_AXI_DATA_WIDTH-1:0] S_AXI_RDATA,
output wire [2-1:0] S_AXI_RRESP,
output wire S_AXI_RLAST,
output wire [C_AXI_RUSER_WIDTH-1:0] S_AXI_RUSER,
output wire S_AXI_RVALID,
input wire S_AXI_RREADY,
// Master Interface Write Address Port
output wire [C_AXI_ID_WIDTH-1:0] M_AXI_AWID,
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_AWADDR,
output wire [4-1:0] M_AXI_AWLEN,
output wire [3-1:0] M_AXI_AWSIZE,
output wire [2-1:0] M_AXI_AWBURST,
output wire [2-1:0] M_AXI_AWLOCK,
output wire [4-1:0] M_AXI_AWCACHE,
output wire [3-1:0] M_AXI_AWPROT,
output wire [C_AXI_AWUSER_WIDTH-1:0] M_AXI_AWUSER,
output wire M_AXI_AWVALID,
input wire M_AXI_AWREADY,
// Master Interface Write Data Ports
output wire [C_AXI_ID_WIDTH-1:0] M_AXI_WID,
output wire [C_AXI_DATA_WIDTH-1:0] M_AXI_WDATA,
output wire [C_AXI_DATA_WIDTH/8-1:0] M_AXI_WSTRB,
output wire M_AXI_WLAST,
output wire [C_AXI_WUSER_WIDTH-1:0] M_AXI_WUSER,
output wire M_AXI_WVALID,
input wire M_AXI_WREADY,
// Master Interface Write Response Ports
input wire [C_AXI_ID_WIDTH-1:0] M_AXI_BID,
input wire [2-1:0] M_AXI_BRESP,
input wire [C_AXI_BUSER_WIDTH-1:0] M_AXI_BUSER,
input wire M_AXI_BVALID,
output wire M_AXI_BREADY,
// Master Interface Read Address Port
output wire [C_AXI_ID_WIDTH-1:0] M_AXI_ARID,
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_ARADDR,
output wire [4-1:0] M_AXI_ARLEN,
output wire [3-1:0] M_AXI_ARSIZE,
output wire [2-1:0] M_AXI_ARBURST,
output wire [2-1:0] M_AXI_ARLOCK,
output wire [4-1:0] M_AXI_ARCACHE,
output wire [3-1:0] M_AXI_ARPROT,
output wire [C_AXI_ARUSER_WIDTH-1:0] M_AXI_ARUSER,
output wire M_AXI_ARVALID,
input wire M_AXI_ARREADY,
// Master Interface Read Data Ports
input wire [C_AXI_ID_WIDTH-1:0] M_AXI_RID,
input wire [C_AXI_DATA_WIDTH-1:0] M_AXI_RDATA,
input wire [2-1:0] M_AXI_RRESP,
input wire M_AXI_RLAST,
input wire [C_AXI_RUSER_WIDTH-1:0] M_AXI_RUSER,
input wire M_AXI_RVALID,
output wire M_AXI_RREADY,
output wire ERROR_TRIGGER,
output wire [C_AXI_ID_WIDTH-1:0] ERROR_TRANSACTION_ID
);
/////////////////////////////////////////////////////////////////////////////
// Functions
/////////////////////////////////////////////////////////////////////////////
/////////////////////////////////////////////////////////////////////////////
// Local params
/////////////////////////////////////////////////////////////////////////////
localparam C_FIFO_DEPTH_LOG = 4;
/////////////////////////////////////////////////////////////////////////////
// Internal signals
/////////////////////////////////////////////////////////////////////////////
// Internal reset.
reg ARESET;
// AW->W command queue signals.
wire cmd_w_valid;
wire cmd_w_check;
wire [C_AXI_ID_WIDTH-1:0] cmd_w_id;
wire cmd_w_ready;
// W->B command queue signals.
wire cmd_b_push;
wire cmd_b_error;
wire [C_AXI_ID_WIDTH-1:0] cmd_b_id;
wire cmd_b_full;
wire [C_FIFO_DEPTH_LOG-1:0] cmd_b_addr;
wire cmd_b_ready;
/////////////////////////////////////////////////////////////////////////////
// Handle Internal Reset
/////////////////////////////////////////////////////////////////////////////
always @ (posedge ACLK) begin
ARESET <= !ARESETN;
end
/////////////////////////////////////////////////////////////////////////////
// Handle Write Channels (AW/W/B)
/////////////////////////////////////////////////////////////////////////////
// Write Address Channel.
processing_system7_v5_5_aw_atc #
(
.C_FAMILY (C_FAMILY),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_AXI_ADDR_WIDTH (C_AXI_ADDR_WIDTH),
.C_AXI_AWUSER_WIDTH (C_AXI_AWUSER_WIDTH),
.C_FIFO_DEPTH_LOG (C_FIFO_DEPTH_LOG)
) write_addr_inst
(
// Global Signals
.ARESET (ARESET),
.ACLK (ACLK),
// Command Interface (Out)
.cmd_w_valid (cmd_w_valid),
.cmd_w_check (cmd_w_check),
.cmd_w_id (cmd_w_id),
.cmd_w_ready (cmd_w_ready),
.cmd_b_addr (cmd_b_addr),
.cmd_b_ready (cmd_b_ready),
// Slave Interface Write Address Ports
.S_AXI_AWID (S_AXI_AWID),
.S_AXI_AWADDR (S_AXI_AWADDR),
.S_AXI_AWLEN (S_AXI_AWLEN),
.S_AXI_AWSIZE (S_AXI_AWSIZE),
.S_AXI_AWBURST (S_AXI_AWBURST),
.S_AXI_AWLOCK (S_AXI_AWLOCK),
.S_AXI_AWCACHE (S_AXI_AWCACHE),
.S_AXI_AWPROT (S_AXI_AWPROT),
.S_AXI_AWUSER (S_AXI_AWUSER),
.S_AXI_AWVALID (S_AXI_AWVALID),
.S_AXI_AWREADY (S_AXI_AWREADY),
// Master Interface Write Address Port
.M_AXI_AWID (M_AXI_AWID),
.M_AXI_AWADDR (M_AXI_AWADDR),
.M_AXI_AWLEN (M_AXI_AWLEN),
.M_AXI_AWSIZE (M_AXI_AWSIZE),
.M_AXI_AWBURST (M_AXI_AWBURST),
.M_AXI_AWLOCK (M_AXI_AWLOCK),
.M_AXI_AWCACHE (M_AXI_AWCACHE),
.M_AXI_AWPROT (M_AXI_AWPROT),
.M_AXI_AWUSER (M_AXI_AWUSER),
.M_AXI_AWVALID (M_AXI_AWVALID),
.M_AXI_AWREADY (M_AXI_AWREADY)
);
// Write Data channel.
processing_system7_v5_5_w_atc #
(
.C_FAMILY (C_FAMILY),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_AXI_DATA_WIDTH (C_AXI_DATA_WIDTH),
.C_AXI_WUSER_WIDTH (C_AXI_WUSER_WIDTH)
) write_data_inst
(
// Global Signals
.ARESET (ARESET),
.ACLK (ACLK),
// Command Interface (In)
.cmd_w_valid (cmd_w_valid),
.cmd_w_check (cmd_w_check),
.cmd_w_id (cmd_w_id),
.cmd_w_ready (cmd_w_ready),
// Command Interface (Out)
.cmd_b_push (cmd_b_push),
.cmd_b_error (cmd_b_error),
.cmd_b_id (cmd_b_id),
.cmd_b_full (cmd_b_full),
// Slave Interface Write Data Ports
.S_AXI_WID (S_AXI_WID),
.S_AXI_WDATA (S_AXI_WDATA),
.S_AXI_WSTRB (S_AXI_WSTRB),
.S_AXI_WLAST (S_AXI_WLAST),
.S_AXI_WUSER (S_AXI_WUSER),
.S_AXI_WVALID (S_AXI_WVALID),
.S_AXI_WREADY (S_AXI_WREADY),
// Master Interface Write Data Ports
.M_AXI_WID (M_AXI_WID),
.M_AXI_WDATA (M_AXI_WDATA),
.M_AXI_WSTRB (M_AXI_WSTRB),
.M_AXI_WLAST (M_AXI_WLAST),
.M_AXI_WUSER (M_AXI_WUSER),
.M_AXI_WVALID (M_AXI_WVALID),
.M_AXI_WREADY (M_AXI_WREADY)
);
// Write Response channel.
processing_system7_v5_5_b_atc #
(
.C_FAMILY (C_FAMILY),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_AXI_BUSER_WIDTH (C_AXI_BUSER_WIDTH),
.C_FIFO_DEPTH_LOG (C_FIFO_DEPTH_LOG)
) write_response_inst
(
// Global Signals
.ARESET (ARESET),
.ACLK (ACLK),
// Command Interface (In)
.cmd_b_push (cmd_b_push),
.cmd_b_error (cmd_b_error),
.cmd_b_id (cmd_b_id),
.cmd_b_full (cmd_b_full),
.cmd_b_addr (cmd_b_addr),
.cmd_b_ready (cmd_b_ready),
// Slave Interface Write Response Ports
.S_AXI_BID (S_AXI_BID),
.S_AXI_BRESP (S_AXI_BRESP),
.S_AXI_BUSER (S_AXI_BUSER),
.S_AXI_BVALID (S_AXI_BVALID),
.S_AXI_BREADY (S_AXI_BREADY),
// Master Interface Write Response Ports
.M_AXI_BID (M_AXI_BID),
.M_AXI_BRESP (M_AXI_BRESP),
.M_AXI_BUSER (M_AXI_BUSER),
.M_AXI_BVALID (M_AXI_BVALID),
.M_AXI_BREADY (M_AXI_BREADY),
// Trigger detection
.ERROR_TRIGGER (ERROR_TRIGGER),
.ERROR_TRANSACTION_ID (ERROR_TRANSACTION_ID)
);
/////////////////////////////////////////////////////////////////////////////
// Handle Read Channels (AR/R)
/////////////////////////////////////////////////////////////////////////////
// Read Address Port
assign M_AXI_ARID = S_AXI_ARID;
assign M_AXI_ARADDR = S_AXI_ARADDR;
assign M_AXI_ARLEN = S_AXI_ARLEN;
assign M_AXI_ARSIZE = S_AXI_ARSIZE;
assign M_AXI_ARBURST = S_AXI_ARBURST;
assign M_AXI_ARLOCK = S_AXI_ARLOCK;
assign M_AXI_ARCACHE = S_AXI_ARCACHE;
assign M_AXI_ARPROT = S_AXI_ARPROT;
assign M_AXI_ARUSER = S_AXI_ARUSER;
assign M_AXI_ARVALID = S_AXI_ARVALID;
assign S_AXI_ARREADY = M_AXI_ARREADY;
// Read Data Port
assign S_AXI_RID = M_AXI_RID;
assign S_AXI_RDATA = M_AXI_RDATA;
assign S_AXI_RRESP = M_AXI_RRESP;
assign S_AXI_RLAST = M_AXI_RLAST;
assign S_AXI_RUSER = M_AXI_RUSER;
assign S_AXI_RVALID = M_AXI_RVALID;
assign M_AXI_RREADY = S_AXI_RREADY;
endmodule
`default_nettype wire
|
//-----------------------------------------------------------------------------
//-- (c) Copyright 2010 Xilinx, Inc. All rights reserved.
//--
//-- This file contains confidential and proprietary information
//-- of Xilinx, Inc. and is protected under U.S. and
//-- international copyright and other intellectual property
//-- laws.
//--
//-- DISCLAIMER
//-- This disclaimer is not a license and does not grant any
//-- rights to the materials distributed herewith. Except as
//-- otherwise provided in a valid license issued to you by
//-- Xilinx, and to the maximum extent permitted by applicable
//-- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
//-- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
//-- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
//-- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
//-- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
//-- (2) Xilinx shall not be liable (whether in contract or tort,
//-- including negligence, or under any other theory of
//-- liability) for any loss or damage of any kind or nature
//-- related to, arising under or in connection with these
//-- materials, including for any direct, or any indirect,
//-- special, incidental, or consequential loss or damage
//-- (including loss of data, profits, goodwill, or any type of
//-- loss or damage suffered as a result of any action brought
//-- by a third party) even if such damage or loss was
//-- reasonably foreseeable or Xilinx had been advised of the
//-- possibility of the same.
//--
//-- CRITICAL APPLICATIONS
//-- Xilinx products are not designed or intended to be fail-
//-- safe, or for use in any application requiring fail-safe
//-- performance, such as life-support or safety devices or
//-- systems, Class III medical devices, nuclear facilities,
//-- applications related to the deployment of airbags, or any
//-- other applications that could lead to death, personal
//-- injury, or severe property or environmental damage
//-- (individually and collectively, "Critical
//-- Applications"). Customer assumes the sole risk and
//-- liability of any use of Xilinx products in Critical
//-- Applications, subject only to applicable laws and
//-- regulations governing limitations on product liability.
//--
//-- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
//-- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
//
// Description: ACP Transaction Checker
//
// Check for optimized ACP transactions and flag if they are broken.
//
//
//
// Verilog-standard: Verilog 2001
//--------------------------------------------------------------------------
//
// Structure:
// atc
// aw_atc
// w_atc
// b_atc
//
//--------------------------------------------------------------------------
`timescale 1ps/1ps
`default_nettype none
module processing_system7_v5_5_atc #
(
parameter C_FAMILY = "rtl",
// FPGA Family. Current version: virtex6, spartan6 or later.
parameter integer C_AXI_ID_WIDTH = 4,
// Width of all ID signals on SI and MI side of checker.
// Range: >= 1.
parameter integer C_AXI_ADDR_WIDTH = 32,
// Width of all ADDR signals on SI and MI side of checker.
// Range: 32.
parameter integer C_AXI_DATA_WIDTH = 64,
// Width of all DATA signals on SI and MI side of checker.
// Range: 64.
parameter integer C_AXI_AWUSER_WIDTH = 1,
// Width of AWUSER signals.
// Range: >= 1.
parameter integer C_AXI_ARUSER_WIDTH = 1,
// Width of ARUSER signals.
// Range: >= 1.
parameter integer C_AXI_WUSER_WIDTH = 1,
// Width of WUSER signals.
// Range: >= 1.
parameter integer C_AXI_RUSER_WIDTH = 1,
// Width of RUSER signals.
// Range: >= 1.
parameter integer C_AXI_BUSER_WIDTH = 1
// Width of BUSER signals.
// Range: >= 1.
)
(
// Global Signals
input wire ACLK,
input wire ARESETN,
// Slave Interface Write Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_AWADDR,
input wire [4-1:0] S_AXI_AWLEN,
input wire [3-1:0] S_AXI_AWSIZE,
input wire [2-1:0] S_AXI_AWBURST,
input wire [2-1:0] S_AXI_AWLOCK,
input wire [4-1:0] S_AXI_AWCACHE,
input wire [3-1:0] S_AXI_AWPROT,
input wire [C_AXI_AWUSER_WIDTH-1:0] S_AXI_AWUSER,
input wire S_AXI_AWVALID,
output wire S_AXI_AWREADY,
// Slave Interface Write Data Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_WID,
input wire [C_AXI_DATA_WIDTH-1:0] S_AXI_WDATA,
input wire [C_AXI_DATA_WIDTH/8-1:0] S_AXI_WSTRB,
input wire S_AXI_WLAST,
input wire [C_AXI_WUSER_WIDTH-1:0] S_AXI_WUSER,
input wire S_AXI_WVALID,
output wire S_AXI_WREADY,
// Slave Interface Write Response Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID,
output wire [2-1:0] S_AXI_BRESP,
output wire [C_AXI_BUSER_WIDTH-1:0] S_AXI_BUSER,
output wire S_AXI_BVALID,
input wire S_AXI_BREADY,
// Slave Interface Read Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_ARADDR,
input wire [4-1:0] S_AXI_ARLEN,
input wire [3-1:0] S_AXI_ARSIZE,
input wire [2-1:0] S_AXI_ARBURST,
input wire [2-1:0] S_AXI_ARLOCK,
input wire [4-1:0] S_AXI_ARCACHE,
input wire [3-1:0] S_AXI_ARPROT,
input wire [C_AXI_ARUSER_WIDTH-1:0] S_AXI_ARUSER,
input wire S_AXI_ARVALID,
output wire S_AXI_ARREADY,
// Slave Interface Read Data Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID,
output wire [C_AXI_DATA_WIDTH-1:0] S_AXI_RDATA,
output wire [2-1:0] S_AXI_RRESP,
output wire S_AXI_RLAST,
output wire [C_AXI_RUSER_WIDTH-1:0] S_AXI_RUSER,
output wire S_AXI_RVALID,
input wire S_AXI_RREADY,
// Master Interface Write Address Port
output wire [C_AXI_ID_WIDTH-1:0] M_AXI_AWID,
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_AWADDR,
output wire [4-1:0] M_AXI_AWLEN,
output wire [3-1:0] M_AXI_AWSIZE,
output wire [2-1:0] M_AXI_AWBURST,
output wire [2-1:0] M_AXI_AWLOCK,
output wire [4-1:0] M_AXI_AWCACHE,
output wire [3-1:0] M_AXI_AWPROT,
output wire [C_AXI_AWUSER_WIDTH-1:0] M_AXI_AWUSER,
output wire M_AXI_AWVALID,
input wire M_AXI_AWREADY,
// Master Interface Write Data Ports
output wire [C_AXI_ID_WIDTH-1:0] M_AXI_WID,
output wire [C_AXI_DATA_WIDTH-1:0] M_AXI_WDATA,
output wire [C_AXI_DATA_WIDTH/8-1:0] M_AXI_WSTRB,
output wire M_AXI_WLAST,
output wire [C_AXI_WUSER_WIDTH-1:0] M_AXI_WUSER,
output wire M_AXI_WVALID,
input wire M_AXI_WREADY,
// Master Interface Write Response Ports
input wire [C_AXI_ID_WIDTH-1:0] M_AXI_BID,
input wire [2-1:0] M_AXI_BRESP,
input wire [C_AXI_BUSER_WIDTH-1:0] M_AXI_BUSER,
input wire M_AXI_BVALID,
output wire M_AXI_BREADY,
// Master Interface Read Address Port
output wire [C_AXI_ID_WIDTH-1:0] M_AXI_ARID,
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_ARADDR,
output wire [4-1:0] M_AXI_ARLEN,
output wire [3-1:0] M_AXI_ARSIZE,
output wire [2-1:0] M_AXI_ARBURST,
output wire [2-1:0] M_AXI_ARLOCK,
output wire [4-1:0] M_AXI_ARCACHE,
output wire [3-1:0] M_AXI_ARPROT,
output wire [C_AXI_ARUSER_WIDTH-1:0] M_AXI_ARUSER,
output wire M_AXI_ARVALID,
input wire M_AXI_ARREADY,
// Master Interface Read Data Ports
input wire [C_AXI_ID_WIDTH-1:0] M_AXI_RID,
input wire [C_AXI_DATA_WIDTH-1:0] M_AXI_RDATA,
input wire [2-1:0] M_AXI_RRESP,
input wire M_AXI_RLAST,
input wire [C_AXI_RUSER_WIDTH-1:0] M_AXI_RUSER,
input wire M_AXI_RVALID,
output wire M_AXI_RREADY,
output wire ERROR_TRIGGER,
output wire [C_AXI_ID_WIDTH-1:0] ERROR_TRANSACTION_ID
);
/////////////////////////////////////////////////////////////////////////////
// Functions
/////////////////////////////////////////////////////////////////////////////
/////////////////////////////////////////////////////////////////////////////
// Local params
/////////////////////////////////////////////////////////////////////////////
localparam C_FIFO_DEPTH_LOG = 4;
/////////////////////////////////////////////////////////////////////////////
// Internal signals
/////////////////////////////////////////////////////////////////////////////
// Internal reset.
reg ARESET;
// AW->W command queue signals.
wire cmd_w_valid;
wire cmd_w_check;
wire [C_AXI_ID_WIDTH-1:0] cmd_w_id;
wire cmd_w_ready;
// W->B command queue signals.
wire cmd_b_push;
wire cmd_b_error;
wire [C_AXI_ID_WIDTH-1:0] cmd_b_id;
wire cmd_b_full;
wire [C_FIFO_DEPTH_LOG-1:0] cmd_b_addr;
wire cmd_b_ready;
/////////////////////////////////////////////////////////////////////////////
// Handle Internal Reset
/////////////////////////////////////////////////////////////////////////////
always @ (posedge ACLK) begin
ARESET <= !ARESETN;
end
/////////////////////////////////////////////////////////////////////////////
// Handle Write Channels (AW/W/B)
/////////////////////////////////////////////////////////////////////////////
// Write Address Channel.
processing_system7_v5_5_aw_atc #
(
.C_FAMILY (C_FAMILY),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_AXI_ADDR_WIDTH (C_AXI_ADDR_WIDTH),
.C_AXI_AWUSER_WIDTH (C_AXI_AWUSER_WIDTH),
.C_FIFO_DEPTH_LOG (C_FIFO_DEPTH_LOG)
) write_addr_inst
(
// Global Signals
.ARESET (ARESET),
.ACLK (ACLK),
// Command Interface (Out)
.cmd_w_valid (cmd_w_valid),
.cmd_w_check (cmd_w_check),
.cmd_w_id (cmd_w_id),
.cmd_w_ready (cmd_w_ready),
.cmd_b_addr (cmd_b_addr),
.cmd_b_ready (cmd_b_ready),
// Slave Interface Write Address Ports
.S_AXI_AWID (S_AXI_AWID),
.S_AXI_AWADDR (S_AXI_AWADDR),
.S_AXI_AWLEN (S_AXI_AWLEN),
.S_AXI_AWSIZE (S_AXI_AWSIZE),
.S_AXI_AWBURST (S_AXI_AWBURST),
.S_AXI_AWLOCK (S_AXI_AWLOCK),
.S_AXI_AWCACHE (S_AXI_AWCACHE),
.S_AXI_AWPROT (S_AXI_AWPROT),
.S_AXI_AWUSER (S_AXI_AWUSER),
.S_AXI_AWVALID (S_AXI_AWVALID),
.S_AXI_AWREADY (S_AXI_AWREADY),
// Master Interface Write Address Port
.M_AXI_AWID (M_AXI_AWID),
.M_AXI_AWADDR (M_AXI_AWADDR),
.M_AXI_AWLEN (M_AXI_AWLEN),
.M_AXI_AWSIZE (M_AXI_AWSIZE),
.M_AXI_AWBURST (M_AXI_AWBURST),
.M_AXI_AWLOCK (M_AXI_AWLOCK),
.M_AXI_AWCACHE (M_AXI_AWCACHE),
.M_AXI_AWPROT (M_AXI_AWPROT),
.M_AXI_AWUSER (M_AXI_AWUSER),
.M_AXI_AWVALID (M_AXI_AWVALID),
.M_AXI_AWREADY (M_AXI_AWREADY)
);
// Write Data channel.
processing_system7_v5_5_w_atc #
(
.C_FAMILY (C_FAMILY),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_AXI_DATA_WIDTH (C_AXI_DATA_WIDTH),
.C_AXI_WUSER_WIDTH (C_AXI_WUSER_WIDTH)
) write_data_inst
(
// Global Signals
.ARESET (ARESET),
.ACLK (ACLK),
// Command Interface (In)
.cmd_w_valid (cmd_w_valid),
.cmd_w_check (cmd_w_check),
.cmd_w_id (cmd_w_id),
.cmd_w_ready (cmd_w_ready),
// Command Interface (Out)
.cmd_b_push (cmd_b_push),
.cmd_b_error (cmd_b_error),
.cmd_b_id (cmd_b_id),
.cmd_b_full (cmd_b_full),
// Slave Interface Write Data Ports
.S_AXI_WID (S_AXI_WID),
.S_AXI_WDATA (S_AXI_WDATA),
.S_AXI_WSTRB (S_AXI_WSTRB),
.S_AXI_WLAST (S_AXI_WLAST),
.S_AXI_WUSER (S_AXI_WUSER),
.S_AXI_WVALID (S_AXI_WVALID),
.S_AXI_WREADY (S_AXI_WREADY),
// Master Interface Write Data Ports
.M_AXI_WID (M_AXI_WID),
.M_AXI_WDATA (M_AXI_WDATA),
.M_AXI_WSTRB (M_AXI_WSTRB),
.M_AXI_WLAST (M_AXI_WLAST),
.M_AXI_WUSER (M_AXI_WUSER),
.M_AXI_WVALID (M_AXI_WVALID),
.M_AXI_WREADY (M_AXI_WREADY)
);
// Write Response channel.
processing_system7_v5_5_b_atc #
(
.C_FAMILY (C_FAMILY),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_AXI_BUSER_WIDTH (C_AXI_BUSER_WIDTH),
.C_FIFO_DEPTH_LOG (C_FIFO_DEPTH_LOG)
) write_response_inst
(
// Global Signals
.ARESET (ARESET),
.ACLK (ACLK),
// Command Interface (In)
.cmd_b_push (cmd_b_push),
.cmd_b_error (cmd_b_error),
.cmd_b_id (cmd_b_id),
.cmd_b_full (cmd_b_full),
.cmd_b_addr (cmd_b_addr),
.cmd_b_ready (cmd_b_ready),
// Slave Interface Write Response Ports
.S_AXI_BID (S_AXI_BID),
.S_AXI_BRESP (S_AXI_BRESP),
.S_AXI_BUSER (S_AXI_BUSER),
.S_AXI_BVALID (S_AXI_BVALID),
.S_AXI_BREADY (S_AXI_BREADY),
// Master Interface Write Response Ports
.M_AXI_BID (M_AXI_BID),
.M_AXI_BRESP (M_AXI_BRESP),
.M_AXI_BUSER (M_AXI_BUSER),
.M_AXI_BVALID (M_AXI_BVALID),
.M_AXI_BREADY (M_AXI_BREADY),
// Trigger detection
.ERROR_TRIGGER (ERROR_TRIGGER),
.ERROR_TRANSACTION_ID (ERROR_TRANSACTION_ID)
);
/////////////////////////////////////////////////////////////////////////////
// Handle Read Channels (AR/R)
/////////////////////////////////////////////////////////////////////////////
// Read Address Port
assign M_AXI_ARID = S_AXI_ARID;
assign M_AXI_ARADDR = S_AXI_ARADDR;
assign M_AXI_ARLEN = S_AXI_ARLEN;
assign M_AXI_ARSIZE = S_AXI_ARSIZE;
assign M_AXI_ARBURST = S_AXI_ARBURST;
assign M_AXI_ARLOCK = S_AXI_ARLOCK;
assign M_AXI_ARCACHE = S_AXI_ARCACHE;
assign M_AXI_ARPROT = S_AXI_ARPROT;
assign M_AXI_ARUSER = S_AXI_ARUSER;
assign M_AXI_ARVALID = S_AXI_ARVALID;
assign S_AXI_ARREADY = M_AXI_ARREADY;
// Read Data Port
assign S_AXI_RID = M_AXI_RID;
assign S_AXI_RDATA = M_AXI_RDATA;
assign S_AXI_RRESP = M_AXI_RRESP;
assign S_AXI_RLAST = M_AXI_RLAST;
assign S_AXI_RUSER = M_AXI_RUSER;
assign S_AXI_RVALID = M_AXI_RVALID;
assign M_AXI_RREADY = S_AXI_RREADY;
endmodule
`default_nettype wire
|
//-----------------------------------------------------------------------------
//-- (c) Copyright 2010 Xilinx, Inc. All rights reserved.
//--
//-- This file contains confidential and proprietary information
//-- of Xilinx, Inc. and is protected under U.S. and
//-- international copyright and other intellectual property
//-- laws.
//--
//-- DISCLAIMER
//-- This disclaimer is not a license and does not grant any
//-- rights to the materials distributed herewith. Except as
//-- otherwise provided in a valid license issued to you by
//-- Xilinx, and to the maximum extent permitted by applicable
//-- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
//-- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
//-- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
//-- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
//-- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
//-- (2) Xilinx shall not be liable (whether in contract or tort,
//-- including negligence, or under any other theory of
//-- liability) for any loss or damage of any kind or nature
//-- related to, arising under or in connection with these
//-- materials, including for any direct, or any indirect,
//-- special, incidental, or consequential loss or damage
//-- (including loss of data, profits, goodwill, or any type of
//-- loss or damage suffered as a result of any action brought
//-- by a third party) even if such damage or loss was
//-- reasonably foreseeable or Xilinx had been advised of the
//-- possibility of the same.
//--
//-- CRITICAL APPLICATIONS
//-- Xilinx products are not designed or intended to be fail-
//-- safe, or for use in any application requiring fail-safe
//-- performance, such as life-support or safety devices or
//-- systems, Class III medical devices, nuclear facilities,
//-- applications related to the deployment of airbags, or any
//-- other applications that could lead to death, personal
//-- injury, or severe property or environmental damage
//-- (individually and collectively, "Critical
//-- Applications"). Customer assumes the sole risk and
//-- liability of any use of Xilinx products in Critical
//-- Applications, subject only to applicable laws and
//-- regulations governing limitations on product liability.
//--
//-- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
//-- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
//
// Description: ACP Transaction Checker
//
// Check for optimized ACP transactions and flag if they are broken.
//
//
//
// Verilog-standard: Verilog 2001
//--------------------------------------------------------------------------
//
// Structure:
// atc
// aw_atc
// w_atc
// b_atc
//
//--------------------------------------------------------------------------
`timescale 1ps/1ps
`default_nettype none
module processing_system7_v5_5_atc #
(
parameter C_FAMILY = "rtl",
// FPGA Family. Current version: virtex6, spartan6 or later.
parameter integer C_AXI_ID_WIDTH = 4,
// Width of all ID signals on SI and MI side of checker.
// Range: >= 1.
parameter integer C_AXI_ADDR_WIDTH = 32,
// Width of all ADDR signals on SI and MI side of checker.
// Range: 32.
parameter integer C_AXI_DATA_WIDTH = 64,
// Width of all DATA signals on SI and MI side of checker.
// Range: 64.
parameter integer C_AXI_AWUSER_WIDTH = 1,
// Width of AWUSER signals.
// Range: >= 1.
parameter integer C_AXI_ARUSER_WIDTH = 1,
// Width of ARUSER signals.
// Range: >= 1.
parameter integer C_AXI_WUSER_WIDTH = 1,
// Width of WUSER signals.
// Range: >= 1.
parameter integer C_AXI_RUSER_WIDTH = 1,
// Width of RUSER signals.
// Range: >= 1.
parameter integer C_AXI_BUSER_WIDTH = 1
// Width of BUSER signals.
// Range: >= 1.
)
(
// Global Signals
input wire ACLK,
input wire ARESETN,
// Slave Interface Write Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_AWADDR,
input wire [4-1:0] S_AXI_AWLEN,
input wire [3-1:0] S_AXI_AWSIZE,
input wire [2-1:0] S_AXI_AWBURST,
input wire [2-1:0] S_AXI_AWLOCK,
input wire [4-1:0] S_AXI_AWCACHE,
input wire [3-1:0] S_AXI_AWPROT,
input wire [C_AXI_AWUSER_WIDTH-1:0] S_AXI_AWUSER,
input wire S_AXI_AWVALID,
output wire S_AXI_AWREADY,
// Slave Interface Write Data Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_WID,
input wire [C_AXI_DATA_WIDTH-1:0] S_AXI_WDATA,
input wire [C_AXI_DATA_WIDTH/8-1:0] S_AXI_WSTRB,
input wire S_AXI_WLAST,
input wire [C_AXI_WUSER_WIDTH-1:0] S_AXI_WUSER,
input wire S_AXI_WVALID,
output wire S_AXI_WREADY,
// Slave Interface Write Response Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID,
output wire [2-1:0] S_AXI_BRESP,
output wire [C_AXI_BUSER_WIDTH-1:0] S_AXI_BUSER,
output wire S_AXI_BVALID,
input wire S_AXI_BREADY,
// Slave Interface Read Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_ARADDR,
input wire [4-1:0] S_AXI_ARLEN,
input wire [3-1:0] S_AXI_ARSIZE,
input wire [2-1:0] S_AXI_ARBURST,
input wire [2-1:0] S_AXI_ARLOCK,
input wire [4-1:0] S_AXI_ARCACHE,
input wire [3-1:0] S_AXI_ARPROT,
input wire [C_AXI_ARUSER_WIDTH-1:0] S_AXI_ARUSER,
input wire S_AXI_ARVALID,
output wire S_AXI_ARREADY,
// Slave Interface Read Data Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID,
output wire [C_AXI_DATA_WIDTH-1:0] S_AXI_RDATA,
output wire [2-1:0] S_AXI_RRESP,
output wire S_AXI_RLAST,
output wire [C_AXI_RUSER_WIDTH-1:0] S_AXI_RUSER,
output wire S_AXI_RVALID,
input wire S_AXI_RREADY,
// Master Interface Write Address Port
output wire [C_AXI_ID_WIDTH-1:0] M_AXI_AWID,
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_AWADDR,
output wire [4-1:0] M_AXI_AWLEN,
output wire [3-1:0] M_AXI_AWSIZE,
output wire [2-1:0] M_AXI_AWBURST,
output wire [2-1:0] M_AXI_AWLOCK,
output wire [4-1:0] M_AXI_AWCACHE,
output wire [3-1:0] M_AXI_AWPROT,
output wire [C_AXI_AWUSER_WIDTH-1:0] M_AXI_AWUSER,
output wire M_AXI_AWVALID,
input wire M_AXI_AWREADY,
// Master Interface Write Data Ports
output wire [C_AXI_ID_WIDTH-1:0] M_AXI_WID,
output wire [C_AXI_DATA_WIDTH-1:0] M_AXI_WDATA,
output wire [C_AXI_DATA_WIDTH/8-1:0] M_AXI_WSTRB,
output wire M_AXI_WLAST,
output wire [C_AXI_WUSER_WIDTH-1:0] M_AXI_WUSER,
output wire M_AXI_WVALID,
input wire M_AXI_WREADY,
// Master Interface Write Response Ports
input wire [C_AXI_ID_WIDTH-1:0] M_AXI_BID,
input wire [2-1:0] M_AXI_BRESP,
input wire [C_AXI_BUSER_WIDTH-1:0] M_AXI_BUSER,
input wire M_AXI_BVALID,
output wire M_AXI_BREADY,
// Master Interface Read Address Port
output wire [C_AXI_ID_WIDTH-1:0] M_AXI_ARID,
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_ARADDR,
output wire [4-1:0] M_AXI_ARLEN,
output wire [3-1:0] M_AXI_ARSIZE,
output wire [2-1:0] M_AXI_ARBURST,
output wire [2-1:0] M_AXI_ARLOCK,
output wire [4-1:0] M_AXI_ARCACHE,
output wire [3-1:0] M_AXI_ARPROT,
output wire [C_AXI_ARUSER_WIDTH-1:0] M_AXI_ARUSER,
output wire M_AXI_ARVALID,
input wire M_AXI_ARREADY,
// Master Interface Read Data Ports
input wire [C_AXI_ID_WIDTH-1:0] M_AXI_RID,
input wire [C_AXI_DATA_WIDTH-1:0] M_AXI_RDATA,
input wire [2-1:0] M_AXI_RRESP,
input wire M_AXI_RLAST,
input wire [C_AXI_RUSER_WIDTH-1:0] M_AXI_RUSER,
input wire M_AXI_RVALID,
output wire M_AXI_RREADY,
output wire ERROR_TRIGGER,
output wire [C_AXI_ID_WIDTH-1:0] ERROR_TRANSACTION_ID
);
/////////////////////////////////////////////////////////////////////////////
// Functions
/////////////////////////////////////////////////////////////////////////////
/////////////////////////////////////////////////////////////////////////////
// Local params
/////////////////////////////////////////////////////////////////////////////
localparam C_FIFO_DEPTH_LOG = 4;
/////////////////////////////////////////////////////////////////////////////
// Internal signals
/////////////////////////////////////////////////////////////////////////////
// Internal reset.
reg ARESET;
// AW->W command queue signals.
wire cmd_w_valid;
wire cmd_w_check;
wire [C_AXI_ID_WIDTH-1:0] cmd_w_id;
wire cmd_w_ready;
// W->B command queue signals.
wire cmd_b_push;
wire cmd_b_error;
wire [C_AXI_ID_WIDTH-1:0] cmd_b_id;
wire cmd_b_full;
wire [C_FIFO_DEPTH_LOG-1:0] cmd_b_addr;
wire cmd_b_ready;
/////////////////////////////////////////////////////////////////////////////
// Handle Internal Reset
/////////////////////////////////////////////////////////////////////////////
always @ (posedge ACLK) begin
ARESET <= !ARESETN;
end
/////////////////////////////////////////////////////////////////////////////
// Handle Write Channels (AW/W/B)
/////////////////////////////////////////////////////////////////////////////
// Write Address Channel.
processing_system7_v5_5_aw_atc #
(
.C_FAMILY (C_FAMILY),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_AXI_ADDR_WIDTH (C_AXI_ADDR_WIDTH),
.C_AXI_AWUSER_WIDTH (C_AXI_AWUSER_WIDTH),
.C_FIFO_DEPTH_LOG (C_FIFO_DEPTH_LOG)
) write_addr_inst
(
// Global Signals
.ARESET (ARESET),
.ACLK (ACLK),
// Command Interface (Out)
.cmd_w_valid (cmd_w_valid),
.cmd_w_check (cmd_w_check),
.cmd_w_id (cmd_w_id),
.cmd_w_ready (cmd_w_ready),
.cmd_b_addr (cmd_b_addr),
.cmd_b_ready (cmd_b_ready),
// Slave Interface Write Address Ports
.S_AXI_AWID (S_AXI_AWID),
.S_AXI_AWADDR (S_AXI_AWADDR),
.S_AXI_AWLEN (S_AXI_AWLEN),
.S_AXI_AWSIZE (S_AXI_AWSIZE),
.S_AXI_AWBURST (S_AXI_AWBURST),
.S_AXI_AWLOCK (S_AXI_AWLOCK),
.S_AXI_AWCACHE (S_AXI_AWCACHE),
.S_AXI_AWPROT (S_AXI_AWPROT),
.S_AXI_AWUSER (S_AXI_AWUSER),
.S_AXI_AWVALID (S_AXI_AWVALID),
.S_AXI_AWREADY (S_AXI_AWREADY),
// Master Interface Write Address Port
.M_AXI_AWID (M_AXI_AWID),
.M_AXI_AWADDR (M_AXI_AWADDR),
.M_AXI_AWLEN (M_AXI_AWLEN),
.M_AXI_AWSIZE (M_AXI_AWSIZE),
.M_AXI_AWBURST (M_AXI_AWBURST),
.M_AXI_AWLOCK (M_AXI_AWLOCK),
.M_AXI_AWCACHE (M_AXI_AWCACHE),
.M_AXI_AWPROT (M_AXI_AWPROT),
.M_AXI_AWUSER (M_AXI_AWUSER),
.M_AXI_AWVALID (M_AXI_AWVALID),
.M_AXI_AWREADY (M_AXI_AWREADY)
);
// Write Data channel.
processing_system7_v5_5_w_atc #
(
.C_FAMILY (C_FAMILY),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_AXI_DATA_WIDTH (C_AXI_DATA_WIDTH),
.C_AXI_WUSER_WIDTH (C_AXI_WUSER_WIDTH)
) write_data_inst
(
// Global Signals
.ARESET (ARESET),
.ACLK (ACLK),
// Command Interface (In)
.cmd_w_valid (cmd_w_valid),
.cmd_w_check (cmd_w_check),
.cmd_w_id (cmd_w_id),
.cmd_w_ready (cmd_w_ready),
// Command Interface (Out)
.cmd_b_push (cmd_b_push),
.cmd_b_error (cmd_b_error),
.cmd_b_id (cmd_b_id),
.cmd_b_full (cmd_b_full),
// Slave Interface Write Data Ports
.S_AXI_WID (S_AXI_WID),
.S_AXI_WDATA (S_AXI_WDATA),
.S_AXI_WSTRB (S_AXI_WSTRB),
.S_AXI_WLAST (S_AXI_WLAST),
.S_AXI_WUSER (S_AXI_WUSER),
.S_AXI_WVALID (S_AXI_WVALID),
.S_AXI_WREADY (S_AXI_WREADY),
// Master Interface Write Data Ports
.M_AXI_WID (M_AXI_WID),
.M_AXI_WDATA (M_AXI_WDATA),
.M_AXI_WSTRB (M_AXI_WSTRB),
.M_AXI_WLAST (M_AXI_WLAST),
.M_AXI_WUSER (M_AXI_WUSER),
.M_AXI_WVALID (M_AXI_WVALID),
.M_AXI_WREADY (M_AXI_WREADY)
);
// Write Response channel.
processing_system7_v5_5_b_atc #
(
.C_FAMILY (C_FAMILY),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_AXI_BUSER_WIDTH (C_AXI_BUSER_WIDTH),
.C_FIFO_DEPTH_LOG (C_FIFO_DEPTH_LOG)
) write_response_inst
(
// Global Signals
.ARESET (ARESET),
.ACLK (ACLK),
// Command Interface (In)
.cmd_b_push (cmd_b_push),
.cmd_b_error (cmd_b_error),
.cmd_b_id (cmd_b_id),
.cmd_b_full (cmd_b_full),
.cmd_b_addr (cmd_b_addr),
.cmd_b_ready (cmd_b_ready),
// Slave Interface Write Response Ports
.S_AXI_BID (S_AXI_BID),
.S_AXI_BRESP (S_AXI_BRESP),
.S_AXI_BUSER (S_AXI_BUSER),
.S_AXI_BVALID (S_AXI_BVALID),
.S_AXI_BREADY (S_AXI_BREADY),
// Master Interface Write Response Ports
.M_AXI_BID (M_AXI_BID),
.M_AXI_BRESP (M_AXI_BRESP),
.M_AXI_BUSER (M_AXI_BUSER),
.M_AXI_BVALID (M_AXI_BVALID),
.M_AXI_BREADY (M_AXI_BREADY),
// Trigger detection
.ERROR_TRIGGER (ERROR_TRIGGER),
.ERROR_TRANSACTION_ID (ERROR_TRANSACTION_ID)
);
/////////////////////////////////////////////////////////////////////////////
// Handle Read Channels (AR/R)
/////////////////////////////////////////////////////////////////////////////
// Read Address Port
assign M_AXI_ARID = S_AXI_ARID;
assign M_AXI_ARADDR = S_AXI_ARADDR;
assign M_AXI_ARLEN = S_AXI_ARLEN;
assign M_AXI_ARSIZE = S_AXI_ARSIZE;
assign M_AXI_ARBURST = S_AXI_ARBURST;
assign M_AXI_ARLOCK = S_AXI_ARLOCK;
assign M_AXI_ARCACHE = S_AXI_ARCACHE;
assign M_AXI_ARPROT = S_AXI_ARPROT;
assign M_AXI_ARUSER = S_AXI_ARUSER;
assign M_AXI_ARVALID = S_AXI_ARVALID;
assign S_AXI_ARREADY = M_AXI_ARREADY;
// Read Data Port
assign S_AXI_RID = M_AXI_RID;
assign S_AXI_RDATA = M_AXI_RDATA;
assign S_AXI_RRESP = M_AXI_RRESP;
assign S_AXI_RLAST = M_AXI_RLAST;
assign S_AXI_RUSER = M_AXI_RUSER;
assign S_AXI_RVALID = M_AXI_RVALID;
assign M_AXI_RREADY = S_AXI_RREADY;
endmodule
`default_nettype wire
|
//-----------------------------------------------------------------------------
//-- (c) Copyright 2010 Xilinx, Inc. All rights reserved.
//--
//-- This file contains confidential and proprietary information
//-- of Xilinx, Inc. and is protected under U.S. and
//-- international copyright and other intellectual property
//-- laws.
//--
//-- DISCLAIMER
//-- This disclaimer is not a license and does not grant any
//-- rights to the materials distributed herewith. Except as
//-- otherwise provided in a valid license issued to you by
//-- Xilinx, and to the maximum extent permitted by applicable
//-- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
//-- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
//-- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
//-- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
//-- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
//-- (2) Xilinx shall not be liable (whether in contract or tort,
//-- including negligence, or under any other theory of
//-- liability) for any loss or damage of any kind or nature
//-- related to, arising under or in connection with these
//-- materials, including for any direct, or any indirect,
//-- special, incidental, or consequential loss or damage
//-- (including loss of data, profits, goodwill, or any type of
//-- loss or damage suffered as a result of any action brought
//-- by a third party) even if such damage or loss was
//-- reasonably foreseeable or Xilinx had been advised of the
//-- possibility of the same.
//--
//-- CRITICAL APPLICATIONS
//-- Xilinx products are not designed or intended to be fail-
//-- safe, or for use in any application requiring fail-safe
//-- performance, such as life-support or safety devices or
//-- systems, Class III medical devices, nuclear facilities,
//-- applications related to the deployment of airbags, or any
//-- other applications that could lead to death, personal
//-- injury, or severe property or environmental damage
//-- (individually and collectively, "Critical
//-- Applications"). Customer assumes the sole risk and
//-- liability of any use of Xilinx products in Critical
//-- Applications, subject only to applicable laws and
//-- regulations governing limitations on product liability.
//--
//-- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
//-- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
//
// Description: ACP Transaction Checker
//
// Check for optimized ACP transactions and flag if they are broken.
//
//
//
// Verilog-standard: Verilog 2001
//--------------------------------------------------------------------------
//
// Structure:
// atc
// aw_atc
// w_atc
// b_atc
//
//--------------------------------------------------------------------------
`timescale 1ps/1ps
`default_nettype none
module processing_system7_v5_5_atc #
(
parameter C_FAMILY = "rtl",
// FPGA Family. Current version: virtex6, spartan6 or later.
parameter integer C_AXI_ID_WIDTH = 4,
// Width of all ID signals on SI and MI side of checker.
// Range: >= 1.
parameter integer C_AXI_ADDR_WIDTH = 32,
// Width of all ADDR signals on SI and MI side of checker.
// Range: 32.
parameter integer C_AXI_DATA_WIDTH = 64,
// Width of all DATA signals on SI and MI side of checker.
// Range: 64.
parameter integer C_AXI_AWUSER_WIDTH = 1,
// Width of AWUSER signals.
// Range: >= 1.
parameter integer C_AXI_ARUSER_WIDTH = 1,
// Width of ARUSER signals.
// Range: >= 1.
parameter integer C_AXI_WUSER_WIDTH = 1,
// Width of WUSER signals.
// Range: >= 1.
parameter integer C_AXI_RUSER_WIDTH = 1,
// Width of RUSER signals.
// Range: >= 1.
parameter integer C_AXI_BUSER_WIDTH = 1
// Width of BUSER signals.
// Range: >= 1.
)
(
// Global Signals
input wire ACLK,
input wire ARESETN,
// Slave Interface Write Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_AWADDR,
input wire [4-1:0] S_AXI_AWLEN,
input wire [3-1:0] S_AXI_AWSIZE,
input wire [2-1:0] S_AXI_AWBURST,
input wire [2-1:0] S_AXI_AWLOCK,
input wire [4-1:0] S_AXI_AWCACHE,
input wire [3-1:0] S_AXI_AWPROT,
input wire [C_AXI_AWUSER_WIDTH-1:0] S_AXI_AWUSER,
input wire S_AXI_AWVALID,
output wire S_AXI_AWREADY,
// Slave Interface Write Data Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_WID,
input wire [C_AXI_DATA_WIDTH-1:0] S_AXI_WDATA,
input wire [C_AXI_DATA_WIDTH/8-1:0] S_AXI_WSTRB,
input wire S_AXI_WLAST,
input wire [C_AXI_WUSER_WIDTH-1:0] S_AXI_WUSER,
input wire S_AXI_WVALID,
output wire S_AXI_WREADY,
// Slave Interface Write Response Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID,
output wire [2-1:0] S_AXI_BRESP,
output wire [C_AXI_BUSER_WIDTH-1:0] S_AXI_BUSER,
output wire S_AXI_BVALID,
input wire S_AXI_BREADY,
// Slave Interface Read Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_ARADDR,
input wire [4-1:0] S_AXI_ARLEN,
input wire [3-1:0] S_AXI_ARSIZE,
input wire [2-1:0] S_AXI_ARBURST,
input wire [2-1:0] S_AXI_ARLOCK,
input wire [4-1:0] S_AXI_ARCACHE,
input wire [3-1:0] S_AXI_ARPROT,
input wire [C_AXI_ARUSER_WIDTH-1:0] S_AXI_ARUSER,
input wire S_AXI_ARVALID,
output wire S_AXI_ARREADY,
// Slave Interface Read Data Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID,
output wire [C_AXI_DATA_WIDTH-1:0] S_AXI_RDATA,
output wire [2-1:0] S_AXI_RRESP,
output wire S_AXI_RLAST,
output wire [C_AXI_RUSER_WIDTH-1:0] S_AXI_RUSER,
output wire S_AXI_RVALID,
input wire S_AXI_RREADY,
// Master Interface Write Address Port
output wire [C_AXI_ID_WIDTH-1:0] M_AXI_AWID,
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_AWADDR,
output wire [4-1:0] M_AXI_AWLEN,
output wire [3-1:0] M_AXI_AWSIZE,
output wire [2-1:0] M_AXI_AWBURST,
output wire [2-1:0] M_AXI_AWLOCK,
output wire [4-1:0] M_AXI_AWCACHE,
output wire [3-1:0] M_AXI_AWPROT,
output wire [C_AXI_AWUSER_WIDTH-1:0] M_AXI_AWUSER,
output wire M_AXI_AWVALID,
input wire M_AXI_AWREADY,
// Master Interface Write Data Ports
output wire [C_AXI_ID_WIDTH-1:0] M_AXI_WID,
output wire [C_AXI_DATA_WIDTH-1:0] M_AXI_WDATA,
output wire [C_AXI_DATA_WIDTH/8-1:0] M_AXI_WSTRB,
output wire M_AXI_WLAST,
output wire [C_AXI_WUSER_WIDTH-1:0] M_AXI_WUSER,
output wire M_AXI_WVALID,
input wire M_AXI_WREADY,
// Master Interface Write Response Ports
input wire [C_AXI_ID_WIDTH-1:0] M_AXI_BID,
input wire [2-1:0] M_AXI_BRESP,
input wire [C_AXI_BUSER_WIDTH-1:0] M_AXI_BUSER,
input wire M_AXI_BVALID,
output wire M_AXI_BREADY,
// Master Interface Read Address Port
output wire [C_AXI_ID_WIDTH-1:0] M_AXI_ARID,
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_ARADDR,
output wire [4-1:0] M_AXI_ARLEN,
output wire [3-1:0] M_AXI_ARSIZE,
output wire [2-1:0] M_AXI_ARBURST,
output wire [2-1:0] M_AXI_ARLOCK,
output wire [4-1:0] M_AXI_ARCACHE,
output wire [3-1:0] M_AXI_ARPROT,
output wire [C_AXI_ARUSER_WIDTH-1:0] M_AXI_ARUSER,
output wire M_AXI_ARVALID,
input wire M_AXI_ARREADY,
// Master Interface Read Data Ports
input wire [C_AXI_ID_WIDTH-1:0] M_AXI_RID,
input wire [C_AXI_DATA_WIDTH-1:0] M_AXI_RDATA,
input wire [2-1:0] M_AXI_RRESP,
input wire M_AXI_RLAST,
input wire [C_AXI_RUSER_WIDTH-1:0] M_AXI_RUSER,
input wire M_AXI_RVALID,
output wire M_AXI_RREADY,
output wire ERROR_TRIGGER,
output wire [C_AXI_ID_WIDTH-1:0] ERROR_TRANSACTION_ID
);
/////////////////////////////////////////////////////////////////////////////
// Functions
/////////////////////////////////////////////////////////////////////////////
/////////////////////////////////////////////////////////////////////////////
// Local params
/////////////////////////////////////////////////////////////////////////////
localparam C_FIFO_DEPTH_LOG = 4;
/////////////////////////////////////////////////////////////////////////////
// Internal signals
/////////////////////////////////////////////////////////////////////////////
// Internal reset.
reg ARESET;
// AW->W command queue signals.
wire cmd_w_valid;
wire cmd_w_check;
wire [C_AXI_ID_WIDTH-1:0] cmd_w_id;
wire cmd_w_ready;
// W->B command queue signals.
wire cmd_b_push;
wire cmd_b_error;
wire [C_AXI_ID_WIDTH-1:0] cmd_b_id;
wire cmd_b_full;
wire [C_FIFO_DEPTH_LOG-1:0] cmd_b_addr;
wire cmd_b_ready;
/////////////////////////////////////////////////////////////////////////////
// Handle Internal Reset
/////////////////////////////////////////////////////////////////////////////
always @ (posedge ACLK) begin
ARESET <= !ARESETN;
end
/////////////////////////////////////////////////////////////////////////////
// Handle Write Channels (AW/W/B)
/////////////////////////////////////////////////////////////////////////////
// Write Address Channel.
processing_system7_v5_5_aw_atc #
(
.C_FAMILY (C_FAMILY),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_AXI_ADDR_WIDTH (C_AXI_ADDR_WIDTH),
.C_AXI_AWUSER_WIDTH (C_AXI_AWUSER_WIDTH),
.C_FIFO_DEPTH_LOG (C_FIFO_DEPTH_LOG)
) write_addr_inst
(
// Global Signals
.ARESET (ARESET),
.ACLK (ACLK),
// Command Interface (Out)
.cmd_w_valid (cmd_w_valid),
.cmd_w_check (cmd_w_check),
.cmd_w_id (cmd_w_id),
.cmd_w_ready (cmd_w_ready),
.cmd_b_addr (cmd_b_addr),
.cmd_b_ready (cmd_b_ready),
// Slave Interface Write Address Ports
.S_AXI_AWID (S_AXI_AWID),
.S_AXI_AWADDR (S_AXI_AWADDR),
.S_AXI_AWLEN (S_AXI_AWLEN),
.S_AXI_AWSIZE (S_AXI_AWSIZE),
.S_AXI_AWBURST (S_AXI_AWBURST),
.S_AXI_AWLOCK (S_AXI_AWLOCK),
.S_AXI_AWCACHE (S_AXI_AWCACHE),
.S_AXI_AWPROT (S_AXI_AWPROT),
.S_AXI_AWUSER (S_AXI_AWUSER),
.S_AXI_AWVALID (S_AXI_AWVALID),
.S_AXI_AWREADY (S_AXI_AWREADY),
// Master Interface Write Address Port
.M_AXI_AWID (M_AXI_AWID),
.M_AXI_AWADDR (M_AXI_AWADDR),
.M_AXI_AWLEN (M_AXI_AWLEN),
.M_AXI_AWSIZE (M_AXI_AWSIZE),
.M_AXI_AWBURST (M_AXI_AWBURST),
.M_AXI_AWLOCK (M_AXI_AWLOCK),
.M_AXI_AWCACHE (M_AXI_AWCACHE),
.M_AXI_AWPROT (M_AXI_AWPROT),
.M_AXI_AWUSER (M_AXI_AWUSER),
.M_AXI_AWVALID (M_AXI_AWVALID),
.M_AXI_AWREADY (M_AXI_AWREADY)
);
// Write Data channel.
processing_system7_v5_5_w_atc #
(
.C_FAMILY (C_FAMILY),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_AXI_DATA_WIDTH (C_AXI_DATA_WIDTH),
.C_AXI_WUSER_WIDTH (C_AXI_WUSER_WIDTH)
) write_data_inst
(
// Global Signals
.ARESET (ARESET),
.ACLK (ACLK),
// Command Interface (In)
.cmd_w_valid (cmd_w_valid),
.cmd_w_check (cmd_w_check),
.cmd_w_id (cmd_w_id),
.cmd_w_ready (cmd_w_ready),
// Command Interface (Out)
.cmd_b_push (cmd_b_push),
.cmd_b_error (cmd_b_error),
.cmd_b_id (cmd_b_id),
.cmd_b_full (cmd_b_full),
// Slave Interface Write Data Ports
.S_AXI_WID (S_AXI_WID),
.S_AXI_WDATA (S_AXI_WDATA),
.S_AXI_WSTRB (S_AXI_WSTRB),
.S_AXI_WLAST (S_AXI_WLAST),
.S_AXI_WUSER (S_AXI_WUSER),
.S_AXI_WVALID (S_AXI_WVALID),
.S_AXI_WREADY (S_AXI_WREADY),
// Master Interface Write Data Ports
.M_AXI_WID (M_AXI_WID),
.M_AXI_WDATA (M_AXI_WDATA),
.M_AXI_WSTRB (M_AXI_WSTRB),
.M_AXI_WLAST (M_AXI_WLAST),
.M_AXI_WUSER (M_AXI_WUSER),
.M_AXI_WVALID (M_AXI_WVALID),
.M_AXI_WREADY (M_AXI_WREADY)
);
// Write Response channel.
processing_system7_v5_5_b_atc #
(
.C_FAMILY (C_FAMILY),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_AXI_BUSER_WIDTH (C_AXI_BUSER_WIDTH),
.C_FIFO_DEPTH_LOG (C_FIFO_DEPTH_LOG)
) write_response_inst
(
// Global Signals
.ARESET (ARESET),
.ACLK (ACLK),
// Command Interface (In)
.cmd_b_push (cmd_b_push),
.cmd_b_error (cmd_b_error),
.cmd_b_id (cmd_b_id),
.cmd_b_full (cmd_b_full),
.cmd_b_addr (cmd_b_addr),
.cmd_b_ready (cmd_b_ready),
// Slave Interface Write Response Ports
.S_AXI_BID (S_AXI_BID),
.S_AXI_BRESP (S_AXI_BRESP),
.S_AXI_BUSER (S_AXI_BUSER),
.S_AXI_BVALID (S_AXI_BVALID),
.S_AXI_BREADY (S_AXI_BREADY),
// Master Interface Write Response Ports
.M_AXI_BID (M_AXI_BID),
.M_AXI_BRESP (M_AXI_BRESP),
.M_AXI_BUSER (M_AXI_BUSER),
.M_AXI_BVALID (M_AXI_BVALID),
.M_AXI_BREADY (M_AXI_BREADY),
// Trigger detection
.ERROR_TRIGGER (ERROR_TRIGGER),
.ERROR_TRANSACTION_ID (ERROR_TRANSACTION_ID)
);
/////////////////////////////////////////////////////////////////////////////
// Handle Read Channels (AR/R)
/////////////////////////////////////////////////////////////////////////////
// Read Address Port
assign M_AXI_ARID = S_AXI_ARID;
assign M_AXI_ARADDR = S_AXI_ARADDR;
assign M_AXI_ARLEN = S_AXI_ARLEN;
assign M_AXI_ARSIZE = S_AXI_ARSIZE;
assign M_AXI_ARBURST = S_AXI_ARBURST;
assign M_AXI_ARLOCK = S_AXI_ARLOCK;
assign M_AXI_ARCACHE = S_AXI_ARCACHE;
assign M_AXI_ARPROT = S_AXI_ARPROT;
assign M_AXI_ARUSER = S_AXI_ARUSER;
assign M_AXI_ARVALID = S_AXI_ARVALID;
assign S_AXI_ARREADY = M_AXI_ARREADY;
// Read Data Port
assign S_AXI_RID = M_AXI_RID;
assign S_AXI_RDATA = M_AXI_RDATA;
assign S_AXI_RRESP = M_AXI_RRESP;
assign S_AXI_RLAST = M_AXI_RLAST;
assign S_AXI_RUSER = M_AXI_RUSER;
assign S_AXI_RVALID = M_AXI_RVALID;
assign M_AXI_RREADY = S_AXI_RREADY;
endmodule
`default_nettype wire
|
//-----------------------------------------------------------------------------
//-- (c) Copyright 2010 Xilinx, Inc. All rights reserved.
//--
//-- This file contains confidential and proprietary information
//-- of Xilinx, Inc. and is protected under U.S. and
//-- international copyright and other intellectual property
//-- laws.
//--
//-- DISCLAIMER
//-- This disclaimer is not a license and does not grant any
//-- rights to the materials distributed herewith. Except as
//-- otherwise provided in a valid license issued to you by
//-- Xilinx, and to the maximum extent permitted by applicable
//-- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
//-- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
//-- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
//-- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
//-- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
//-- (2) Xilinx shall not be liable (whether in contract or tort,
//-- including negligence, or under any other theory of
//-- liability) for any loss or damage of any kind or nature
//-- related to, arising under or in connection with these
//-- materials, including for any direct, or any indirect,
//-- special, incidental, or consequential loss or damage
//-- (including loss of data, profits, goodwill, or any type of
//-- loss or damage suffered as a result of any action brought
//-- by a third party) even if such damage or loss was
//-- reasonably foreseeable or Xilinx had been advised of the
//-- possibility of the same.
//--
//-- CRITICAL APPLICATIONS
//-- Xilinx products are not designed or intended to be fail-
//-- safe, or for use in any application requiring fail-safe
//-- performance, such as life-support or safety devices or
//-- systems, Class III medical devices, nuclear facilities,
//-- applications related to the deployment of airbags, or any
//-- other applications that could lead to death, personal
//-- injury, or severe property or environmental damage
//-- (individually and collectively, "Critical
//-- Applications"). Customer assumes the sole risk and
//-- liability of any use of Xilinx products in Critical
//-- Applications, subject only to applicable laws and
//-- regulations governing limitations on product liability.
//--
//-- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
//-- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
//
// Description: ACP Transaction Checker
//
// Check for optimized ACP transactions and flag if they are broken.
//
//
//
// Verilog-standard: Verilog 2001
//--------------------------------------------------------------------------
//
// Structure:
// atc
// aw_atc
// w_atc
// b_atc
//
//--------------------------------------------------------------------------
`timescale 1ps/1ps
`default_nettype none
module processing_system7_v5_5_atc #
(
parameter C_FAMILY = "rtl",
// FPGA Family. Current version: virtex6, spartan6 or later.
parameter integer C_AXI_ID_WIDTH = 4,
// Width of all ID signals on SI and MI side of checker.
// Range: >= 1.
parameter integer C_AXI_ADDR_WIDTH = 32,
// Width of all ADDR signals on SI and MI side of checker.
// Range: 32.
parameter integer C_AXI_DATA_WIDTH = 64,
// Width of all DATA signals on SI and MI side of checker.
// Range: 64.
parameter integer C_AXI_AWUSER_WIDTH = 1,
// Width of AWUSER signals.
// Range: >= 1.
parameter integer C_AXI_ARUSER_WIDTH = 1,
// Width of ARUSER signals.
// Range: >= 1.
parameter integer C_AXI_WUSER_WIDTH = 1,
// Width of WUSER signals.
// Range: >= 1.
parameter integer C_AXI_RUSER_WIDTH = 1,
// Width of RUSER signals.
// Range: >= 1.
parameter integer C_AXI_BUSER_WIDTH = 1
// Width of BUSER signals.
// Range: >= 1.
)
(
// Global Signals
input wire ACLK,
input wire ARESETN,
// Slave Interface Write Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_AWADDR,
input wire [4-1:0] S_AXI_AWLEN,
input wire [3-1:0] S_AXI_AWSIZE,
input wire [2-1:0] S_AXI_AWBURST,
input wire [2-1:0] S_AXI_AWLOCK,
input wire [4-1:0] S_AXI_AWCACHE,
input wire [3-1:0] S_AXI_AWPROT,
input wire [C_AXI_AWUSER_WIDTH-1:0] S_AXI_AWUSER,
input wire S_AXI_AWVALID,
output wire S_AXI_AWREADY,
// Slave Interface Write Data Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_WID,
input wire [C_AXI_DATA_WIDTH-1:0] S_AXI_WDATA,
input wire [C_AXI_DATA_WIDTH/8-1:0] S_AXI_WSTRB,
input wire S_AXI_WLAST,
input wire [C_AXI_WUSER_WIDTH-1:0] S_AXI_WUSER,
input wire S_AXI_WVALID,
output wire S_AXI_WREADY,
// Slave Interface Write Response Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID,
output wire [2-1:0] S_AXI_BRESP,
output wire [C_AXI_BUSER_WIDTH-1:0] S_AXI_BUSER,
output wire S_AXI_BVALID,
input wire S_AXI_BREADY,
// Slave Interface Read Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_ARADDR,
input wire [4-1:0] S_AXI_ARLEN,
input wire [3-1:0] S_AXI_ARSIZE,
input wire [2-1:0] S_AXI_ARBURST,
input wire [2-1:0] S_AXI_ARLOCK,
input wire [4-1:0] S_AXI_ARCACHE,
input wire [3-1:0] S_AXI_ARPROT,
input wire [C_AXI_ARUSER_WIDTH-1:0] S_AXI_ARUSER,
input wire S_AXI_ARVALID,
output wire S_AXI_ARREADY,
// Slave Interface Read Data Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID,
output wire [C_AXI_DATA_WIDTH-1:0] S_AXI_RDATA,
output wire [2-1:0] S_AXI_RRESP,
output wire S_AXI_RLAST,
output wire [C_AXI_RUSER_WIDTH-1:0] S_AXI_RUSER,
output wire S_AXI_RVALID,
input wire S_AXI_RREADY,
// Master Interface Write Address Port
output wire [C_AXI_ID_WIDTH-1:0] M_AXI_AWID,
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_AWADDR,
output wire [4-1:0] M_AXI_AWLEN,
output wire [3-1:0] M_AXI_AWSIZE,
output wire [2-1:0] M_AXI_AWBURST,
output wire [2-1:0] M_AXI_AWLOCK,
output wire [4-1:0] M_AXI_AWCACHE,
output wire [3-1:0] M_AXI_AWPROT,
output wire [C_AXI_AWUSER_WIDTH-1:0] M_AXI_AWUSER,
output wire M_AXI_AWVALID,
input wire M_AXI_AWREADY,
// Master Interface Write Data Ports
output wire [C_AXI_ID_WIDTH-1:0] M_AXI_WID,
output wire [C_AXI_DATA_WIDTH-1:0] M_AXI_WDATA,
output wire [C_AXI_DATA_WIDTH/8-1:0] M_AXI_WSTRB,
output wire M_AXI_WLAST,
output wire [C_AXI_WUSER_WIDTH-1:0] M_AXI_WUSER,
output wire M_AXI_WVALID,
input wire M_AXI_WREADY,
// Master Interface Write Response Ports
input wire [C_AXI_ID_WIDTH-1:0] M_AXI_BID,
input wire [2-1:0] M_AXI_BRESP,
input wire [C_AXI_BUSER_WIDTH-1:0] M_AXI_BUSER,
input wire M_AXI_BVALID,
output wire M_AXI_BREADY,
// Master Interface Read Address Port
output wire [C_AXI_ID_WIDTH-1:0] M_AXI_ARID,
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_ARADDR,
output wire [4-1:0] M_AXI_ARLEN,
output wire [3-1:0] M_AXI_ARSIZE,
output wire [2-1:0] M_AXI_ARBURST,
output wire [2-1:0] M_AXI_ARLOCK,
output wire [4-1:0] M_AXI_ARCACHE,
output wire [3-1:0] M_AXI_ARPROT,
output wire [C_AXI_ARUSER_WIDTH-1:0] M_AXI_ARUSER,
output wire M_AXI_ARVALID,
input wire M_AXI_ARREADY,
// Master Interface Read Data Ports
input wire [C_AXI_ID_WIDTH-1:0] M_AXI_RID,
input wire [C_AXI_DATA_WIDTH-1:0] M_AXI_RDATA,
input wire [2-1:0] M_AXI_RRESP,
input wire M_AXI_RLAST,
input wire [C_AXI_RUSER_WIDTH-1:0] M_AXI_RUSER,
input wire M_AXI_RVALID,
output wire M_AXI_RREADY,
output wire ERROR_TRIGGER,
output wire [C_AXI_ID_WIDTH-1:0] ERROR_TRANSACTION_ID
);
/////////////////////////////////////////////////////////////////////////////
// Functions
/////////////////////////////////////////////////////////////////////////////
/////////////////////////////////////////////////////////////////////////////
// Local params
/////////////////////////////////////////////////////////////////////////////
localparam C_FIFO_DEPTH_LOG = 4;
/////////////////////////////////////////////////////////////////////////////
// Internal signals
/////////////////////////////////////////////////////////////////////////////
// Internal reset.
reg ARESET;
// AW->W command queue signals.
wire cmd_w_valid;
wire cmd_w_check;
wire [C_AXI_ID_WIDTH-1:0] cmd_w_id;
wire cmd_w_ready;
// W->B command queue signals.
wire cmd_b_push;
wire cmd_b_error;
wire [C_AXI_ID_WIDTH-1:0] cmd_b_id;
wire cmd_b_full;
wire [C_FIFO_DEPTH_LOG-1:0] cmd_b_addr;
wire cmd_b_ready;
/////////////////////////////////////////////////////////////////////////////
// Handle Internal Reset
/////////////////////////////////////////////////////////////////////////////
always @ (posedge ACLK) begin
ARESET <= !ARESETN;
end
/////////////////////////////////////////////////////////////////////////////
// Handle Write Channels (AW/W/B)
/////////////////////////////////////////////////////////////////////////////
// Write Address Channel.
processing_system7_v5_5_aw_atc #
(
.C_FAMILY (C_FAMILY),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_AXI_ADDR_WIDTH (C_AXI_ADDR_WIDTH),
.C_AXI_AWUSER_WIDTH (C_AXI_AWUSER_WIDTH),
.C_FIFO_DEPTH_LOG (C_FIFO_DEPTH_LOG)
) write_addr_inst
(
// Global Signals
.ARESET (ARESET),
.ACLK (ACLK),
// Command Interface (Out)
.cmd_w_valid (cmd_w_valid),
.cmd_w_check (cmd_w_check),
.cmd_w_id (cmd_w_id),
.cmd_w_ready (cmd_w_ready),
.cmd_b_addr (cmd_b_addr),
.cmd_b_ready (cmd_b_ready),
// Slave Interface Write Address Ports
.S_AXI_AWID (S_AXI_AWID),
.S_AXI_AWADDR (S_AXI_AWADDR),
.S_AXI_AWLEN (S_AXI_AWLEN),
.S_AXI_AWSIZE (S_AXI_AWSIZE),
.S_AXI_AWBURST (S_AXI_AWBURST),
.S_AXI_AWLOCK (S_AXI_AWLOCK),
.S_AXI_AWCACHE (S_AXI_AWCACHE),
.S_AXI_AWPROT (S_AXI_AWPROT),
.S_AXI_AWUSER (S_AXI_AWUSER),
.S_AXI_AWVALID (S_AXI_AWVALID),
.S_AXI_AWREADY (S_AXI_AWREADY),
// Master Interface Write Address Port
.M_AXI_AWID (M_AXI_AWID),
.M_AXI_AWADDR (M_AXI_AWADDR),
.M_AXI_AWLEN (M_AXI_AWLEN),
.M_AXI_AWSIZE (M_AXI_AWSIZE),
.M_AXI_AWBURST (M_AXI_AWBURST),
.M_AXI_AWLOCK (M_AXI_AWLOCK),
.M_AXI_AWCACHE (M_AXI_AWCACHE),
.M_AXI_AWPROT (M_AXI_AWPROT),
.M_AXI_AWUSER (M_AXI_AWUSER),
.M_AXI_AWVALID (M_AXI_AWVALID),
.M_AXI_AWREADY (M_AXI_AWREADY)
);
// Write Data channel.
processing_system7_v5_5_w_atc #
(
.C_FAMILY (C_FAMILY),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_AXI_DATA_WIDTH (C_AXI_DATA_WIDTH),
.C_AXI_WUSER_WIDTH (C_AXI_WUSER_WIDTH)
) write_data_inst
(
// Global Signals
.ARESET (ARESET),
.ACLK (ACLK),
// Command Interface (In)
.cmd_w_valid (cmd_w_valid),
.cmd_w_check (cmd_w_check),
.cmd_w_id (cmd_w_id),
.cmd_w_ready (cmd_w_ready),
// Command Interface (Out)
.cmd_b_push (cmd_b_push),
.cmd_b_error (cmd_b_error),
.cmd_b_id (cmd_b_id),
.cmd_b_full (cmd_b_full),
// Slave Interface Write Data Ports
.S_AXI_WID (S_AXI_WID),
.S_AXI_WDATA (S_AXI_WDATA),
.S_AXI_WSTRB (S_AXI_WSTRB),
.S_AXI_WLAST (S_AXI_WLAST),
.S_AXI_WUSER (S_AXI_WUSER),
.S_AXI_WVALID (S_AXI_WVALID),
.S_AXI_WREADY (S_AXI_WREADY),
// Master Interface Write Data Ports
.M_AXI_WID (M_AXI_WID),
.M_AXI_WDATA (M_AXI_WDATA),
.M_AXI_WSTRB (M_AXI_WSTRB),
.M_AXI_WLAST (M_AXI_WLAST),
.M_AXI_WUSER (M_AXI_WUSER),
.M_AXI_WVALID (M_AXI_WVALID),
.M_AXI_WREADY (M_AXI_WREADY)
);
// Write Response channel.
processing_system7_v5_5_b_atc #
(
.C_FAMILY (C_FAMILY),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_AXI_BUSER_WIDTH (C_AXI_BUSER_WIDTH),
.C_FIFO_DEPTH_LOG (C_FIFO_DEPTH_LOG)
) write_response_inst
(
// Global Signals
.ARESET (ARESET),
.ACLK (ACLK),
// Command Interface (In)
.cmd_b_push (cmd_b_push),
.cmd_b_error (cmd_b_error),
.cmd_b_id (cmd_b_id),
.cmd_b_full (cmd_b_full),
.cmd_b_addr (cmd_b_addr),
.cmd_b_ready (cmd_b_ready),
// Slave Interface Write Response Ports
.S_AXI_BID (S_AXI_BID),
.S_AXI_BRESP (S_AXI_BRESP),
.S_AXI_BUSER (S_AXI_BUSER),
.S_AXI_BVALID (S_AXI_BVALID),
.S_AXI_BREADY (S_AXI_BREADY),
// Master Interface Write Response Ports
.M_AXI_BID (M_AXI_BID),
.M_AXI_BRESP (M_AXI_BRESP),
.M_AXI_BUSER (M_AXI_BUSER),
.M_AXI_BVALID (M_AXI_BVALID),
.M_AXI_BREADY (M_AXI_BREADY),
// Trigger detection
.ERROR_TRIGGER (ERROR_TRIGGER),
.ERROR_TRANSACTION_ID (ERROR_TRANSACTION_ID)
);
/////////////////////////////////////////////////////////////////////////////
// Handle Read Channels (AR/R)
/////////////////////////////////////////////////////////////////////////////
// Read Address Port
assign M_AXI_ARID = S_AXI_ARID;
assign M_AXI_ARADDR = S_AXI_ARADDR;
assign M_AXI_ARLEN = S_AXI_ARLEN;
assign M_AXI_ARSIZE = S_AXI_ARSIZE;
assign M_AXI_ARBURST = S_AXI_ARBURST;
assign M_AXI_ARLOCK = S_AXI_ARLOCK;
assign M_AXI_ARCACHE = S_AXI_ARCACHE;
assign M_AXI_ARPROT = S_AXI_ARPROT;
assign M_AXI_ARUSER = S_AXI_ARUSER;
assign M_AXI_ARVALID = S_AXI_ARVALID;
assign S_AXI_ARREADY = M_AXI_ARREADY;
// Read Data Port
assign S_AXI_RID = M_AXI_RID;
assign S_AXI_RDATA = M_AXI_RDATA;
assign S_AXI_RRESP = M_AXI_RRESP;
assign S_AXI_RLAST = M_AXI_RLAST;
assign S_AXI_RUSER = M_AXI_RUSER;
assign S_AXI_RVALID = M_AXI_RVALID;
assign M_AXI_RREADY = S_AXI_RREADY;
endmodule
`default_nettype wire
|
//-----------------------------------------------------------------------------
//-- (c) Copyright 2010 Xilinx, Inc. All rights reserved.
//--
//-- This file contains confidential and proprietary information
//-- of Xilinx, Inc. and is protected under U.S. and
//-- international copyright and other intellectual property
//-- laws.
//--
//-- DISCLAIMER
//-- This disclaimer is not a license and does not grant any
//-- rights to the materials distributed herewith. Except as
//-- otherwise provided in a valid license issued to you by
//-- Xilinx, and to the maximum extent permitted by applicable
//-- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
//-- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
//-- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
//-- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
//-- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
//-- (2) Xilinx shall not be liable (whether in contract or tort,
//-- including negligence, or under any other theory of
//-- liability) for any loss or damage of any kind or nature
//-- related to, arising under or in connection with these
//-- materials, including for any direct, or any indirect,
//-- special, incidental, or consequential loss or damage
//-- (including loss of data, profits, goodwill, or any type of
//-- loss or damage suffered as a result of any action brought
//-- by a third party) even if such damage or loss was
//-- reasonably foreseeable or Xilinx had been advised of the
//-- possibility of the same.
//--
//-- CRITICAL APPLICATIONS
//-- Xilinx products are not designed or intended to be fail-
//-- safe, or for use in any application requiring fail-safe
//-- performance, such as life-support or safety devices or
//-- systems, Class III medical devices, nuclear facilities,
//-- applications related to the deployment of airbags, or any
//-- other applications that could lead to death, personal
//-- injury, or severe property or environmental damage
//-- (individually and collectively, "Critical
//-- Applications"). Customer assumes the sole risk and
//-- liability of any use of Xilinx products in Critical
//-- Applications, subject only to applicable laws and
//-- regulations governing limitations on product liability.
//--
//-- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
//-- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
//
// Description: ACP Transaction Checker
//
// Check for optimized ACP transactions and flag if they are broken.
//
//
//
// Verilog-standard: Verilog 2001
//--------------------------------------------------------------------------
//
// Structure:
// atc
// aw_atc
// w_atc
// b_atc
//
//--------------------------------------------------------------------------
`timescale 1ps/1ps
`default_nettype none
module processing_system7_v5_5_atc #
(
parameter C_FAMILY = "rtl",
// FPGA Family. Current version: virtex6, spartan6 or later.
parameter integer C_AXI_ID_WIDTH = 4,
// Width of all ID signals on SI and MI side of checker.
// Range: >= 1.
parameter integer C_AXI_ADDR_WIDTH = 32,
// Width of all ADDR signals on SI and MI side of checker.
// Range: 32.
parameter integer C_AXI_DATA_WIDTH = 64,
// Width of all DATA signals on SI and MI side of checker.
// Range: 64.
parameter integer C_AXI_AWUSER_WIDTH = 1,
// Width of AWUSER signals.
// Range: >= 1.
parameter integer C_AXI_ARUSER_WIDTH = 1,
// Width of ARUSER signals.
// Range: >= 1.
parameter integer C_AXI_WUSER_WIDTH = 1,
// Width of WUSER signals.
// Range: >= 1.
parameter integer C_AXI_RUSER_WIDTH = 1,
// Width of RUSER signals.
// Range: >= 1.
parameter integer C_AXI_BUSER_WIDTH = 1
// Width of BUSER signals.
// Range: >= 1.
)
(
// Global Signals
input wire ACLK,
input wire ARESETN,
// Slave Interface Write Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_AWADDR,
input wire [4-1:0] S_AXI_AWLEN,
input wire [3-1:0] S_AXI_AWSIZE,
input wire [2-1:0] S_AXI_AWBURST,
input wire [2-1:0] S_AXI_AWLOCK,
input wire [4-1:0] S_AXI_AWCACHE,
input wire [3-1:0] S_AXI_AWPROT,
input wire [C_AXI_AWUSER_WIDTH-1:0] S_AXI_AWUSER,
input wire S_AXI_AWVALID,
output wire S_AXI_AWREADY,
// Slave Interface Write Data Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_WID,
input wire [C_AXI_DATA_WIDTH-1:0] S_AXI_WDATA,
input wire [C_AXI_DATA_WIDTH/8-1:0] S_AXI_WSTRB,
input wire S_AXI_WLAST,
input wire [C_AXI_WUSER_WIDTH-1:0] S_AXI_WUSER,
input wire S_AXI_WVALID,
output wire S_AXI_WREADY,
// Slave Interface Write Response Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID,
output wire [2-1:0] S_AXI_BRESP,
output wire [C_AXI_BUSER_WIDTH-1:0] S_AXI_BUSER,
output wire S_AXI_BVALID,
input wire S_AXI_BREADY,
// Slave Interface Read Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_ARADDR,
input wire [4-1:0] S_AXI_ARLEN,
input wire [3-1:0] S_AXI_ARSIZE,
input wire [2-1:0] S_AXI_ARBURST,
input wire [2-1:0] S_AXI_ARLOCK,
input wire [4-1:0] S_AXI_ARCACHE,
input wire [3-1:0] S_AXI_ARPROT,
input wire [C_AXI_ARUSER_WIDTH-1:0] S_AXI_ARUSER,
input wire S_AXI_ARVALID,
output wire S_AXI_ARREADY,
// Slave Interface Read Data Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID,
output wire [C_AXI_DATA_WIDTH-1:0] S_AXI_RDATA,
output wire [2-1:0] S_AXI_RRESP,
output wire S_AXI_RLAST,
output wire [C_AXI_RUSER_WIDTH-1:0] S_AXI_RUSER,
output wire S_AXI_RVALID,
input wire S_AXI_RREADY,
// Master Interface Write Address Port
output wire [C_AXI_ID_WIDTH-1:0] M_AXI_AWID,
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_AWADDR,
output wire [4-1:0] M_AXI_AWLEN,
output wire [3-1:0] M_AXI_AWSIZE,
output wire [2-1:0] M_AXI_AWBURST,
output wire [2-1:0] M_AXI_AWLOCK,
output wire [4-1:0] M_AXI_AWCACHE,
output wire [3-1:0] M_AXI_AWPROT,
output wire [C_AXI_AWUSER_WIDTH-1:0] M_AXI_AWUSER,
output wire M_AXI_AWVALID,
input wire M_AXI_AWREADY,
// Master Interface Write Data Ports
output wire [C_AXI_ID_WIDTH-1:0] M_AXI_WID,
output wire [C_AXI_DATA_WIDTH-1:0] M_AXI_WDATA,
output wire [C_AXI_DATA_WIDTH/8-1:0] M_AXI_WSTRB,
output wire M_AXI_WLAST,
output wire [C_AXI_WUSER_WIDTH-1:0] M_AXI_WUSER,
output wire M_AXI_WVALID,
input wire M_AXI_WREADY,
// Master Interface Write Response Ports
input wire [C_AXI_ID_WIDTH-1:0] M_AXI_BID,
input wire [2-1:0] M_AXI_BRESP,
input wire [C_AXI_BUSER_WIDTH-1:0] M_AXI_BUSER,
input wire M_AXI_BVALID,
output wire M_AXI_BREADY,
// Master Interface Read Address Port
output wire [C_AXI_ID_WIDTH-1:0] M_AXI_ARID,
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_ARADDR,
output wire [4-1:0] M_AXI_ARLEN,
output wire [3-1:0] M_AXI_ARSIZE,
output wire [2-1:0] M_AXI_ARBURST,
output wire [2-1:0] M_AXI_ARLOCK,
output wire [4-1:0] M_AXI_ARCACHE,
output wire [3-1:0] M_AXI_ARPROT,
output wire [C_AXI_ARUSER_WIDTH-1:0] M_AXI_ARUSER,
output wire M_AXI_ARVALID,
input wire M_AXI_ARREADY,
// Master Interface Read Data Ports
input wire [C_AXI_ID_WIDTH-1:0] M_AXI_RID,
input wire [C_AXI_DATA_WIDTH-1:0] M_AXI_RDATA,
input wire [2-1:0] M_AXI_RRESP,
input wire M_AXI_RLAST,
input wire [C_AXI_RUSER_WIDTH-1:0] M_AXI_RUSER,
input wire M_AXI_RVALID,
output wire M_AXI_RREADY,
output wire ERROR_TRIGGER,
output wire [C_AXI_ID_WIDTH-1:0] ERROR_TRANSACTION_ID
);
/////////////////////////////////////////////////////////////////////////////
// Functions
/////////////////////////////////////////////////////////////////////////////
/////////////////////////////////////////////////////////////////////////////
// Local params
/////////////////////////////////////////////////////////////////////////////
localparam C_FIFO_DEPTH_LOG = 4;
/////////////////////////////////////////////////////////////////////////////
// Internal signals
/////////////////////////////////////////////////////////////////////////////
// Internal reset.
reg ARESET;
// AW->W command queue signals.
wire cmd_w_valid;
wire cmd_w_check;
wire [C_AXI_ID_WIDTH-1:0] cmd_w_id;
wire cmd_w_ready;
// W->B command queue signals.
wire cmd_b_push;
wire cmd_b_error;
wire [C_AXI_ID_WIDTH-1:0] cmd_b_id;
wire cmd_b_full;
wire [C_FIFO_DEPTH_LOG-1:0] cmd_b_addr;
wire cmd_b_ready;
/////////////////////////////////////////////////////////////////////////////
// Handle Internal Reset
/////////////////////////////////////////////////////////////////////////////
always @ (posedge ACLK) begin
ARESET <= !ARESETN;
end
/////////////////////////////////////////////////////////////////////////////
// Handle Write Channels (AW/W/B)
/////////////////////////////////////////////////////////////////////////////
// Write Address Channel.
processing_system7_v5_5_aw_atc #
(
.C_FAMILY (C_FAMILY),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_AXI_ADDR_WIDTH (C_AXI_ADDR_WIDTH),
.C_AXI_AWUSER_WIDTH (C_AXI_AWUSER_WIDTH),
.C_FIFO_DEPTH_LOG (C_FIFO_DEPTH_LOG)
) write_addr_inst
(
// Global Signals
.ARESET (ARESET),
.ACLK (ACLK),
// Command Interface (Out)
.cmd_w_valid (cmd_w_valid),
.cmd_w_check (cmd_w_check),
.cmd_w_id (cmd_w_id),
.cmd_w_ready (cmd_w_ready),
.cmd_b_addr (cmd_b_addr),
.cmd_b_ready (cmd_b_ready),
// Slave Interface Write Address Ports
.S_AXI_AWID (S_AXI_AWID),
.S_AXI_AWADDR (S_AXI_AWADDR),
.S_AXI_AWLEN (S_AXI_AWLEN),
.S_AXI_AWSIZE (S_AXI_AWSIZE),
.S_AXI_AWBURST (S_AXI_AWBURST),
.S_AXI_AWLOCK (S_AXI_AWLOCK),
.S_AXI_AWCACHE (S_AXI_AWCACHE),
.S_AXI_AWPROT (S_AXI_AWPROT),
.S_AXI_AWUSER (S_AXI_AWUSER),
.S_AXI_AWVALID (S_AXI_AWVALID),
.S_AXI_AWREADY (S_AXI_AWREADY),
// Master Interface Write Address Port
.M_AXI_AWID (M_AXI_AWID),
.M_AXI_AWADDR (M_AXI_AWADDR),
.M_AXI_AWLEN (M_AXI_AWLEN),
.M_AXI_AWSIZE (M_AXI_AWSIZE),
.M_AXI_AWBURST (M_AXI_AWBURST),
.M_AXI_AWLOCK (M_AXI_AWLOCK),
.M_AXI_AWCACHE (M_AXI_AWCACHE),
.M_AXI_AWPROT (M_AXI_AWPROT),
.M_AXI_AWUSER (M_AXI_AWUSER),
.M_AXI_AWVALID (M_AXI_AWVALID),
.M_AXI_AWREADY (M_AXI_AWREADY)
);
// Write Data channel.
processing_system7_v5_5_w_atc #
(
.C_FAMILY (C_FAMILY),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_AXI_DATA_WIDTH (C_AXI_DATA_WIDTH),
.C_AXI_WUSER_WIDTH (C_AXI_WUSER_WIDTH)
) write_data_inst
(
// Global Signals
.ARESET (ARESET),
.ACLK (ACLK),
// Command Interface (In)
.cmd_w_valid (cmd_w_valid),
.cmd_w_check (cmd_w_check),
.cmd_w_id (cmd_w_id),
.cmd_w_ready (cmd_w_ready),
// Command Interface (Out)
.cmd_b_push (cmd_b_push),
.cmd_b_error (cmd_b_error),
.cmd_b_id (cmd_b_id),
.cmd_b_full (cmd_b_full),
// Slave Interface Write Data Ports
.S_AXI_WID (S_AXI_WID),
.S_AXI_WDATA (S_AXI_WDATA),
.S_AXI_WSTRB (S_AXI_WSTRB),
.S_AXI_WLAST (S_AXI_WLAST),
.S_AXI_WUSER (S_AXI_WUSER),
.S_AXI_WVALID (S_AXI_WVALID),
.S_AXI_WREADY (S_AXI_WREADY),
// Master Interface Write Data Ports
.M_AXI_WID (M_AXI_WID),
.M_AXI_WDATA (M_AXI_WDATA),
.M_AXI_WSTRB (M_AXI_WSTRB),
.M_AXI_WLAST (M_AXI_WLAST),
.M_AXI_WUSER (M_AXI_WUSER),
.M_AXI_WVALID (M_AXI_WVALID),
.M_AXI_WREADY (M_AXI_WREADY)
);
// Write Response channel.
processing_system7_v5_5_b_atc #
(
.C_FAMILY (C_FAMILY),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_AXI_BUSER_WIDTH (C_AXI_BUSER_WIDTH),
.C_FIFO_DEPTH_LOG (C_FIFO_DEPTH_LOG)
) write_response_inst
(
// Global Signals
.ARESET (ARESET),
.ACLK (ACLK),
// Command Interface (In)
.cmd_b_push (cmd_b_push),
.cmd_b_error (cmd_b_error),
.cmd_b_id (cmd_b_id),
.cmd_b_full (cmd_b_full),
.cmd_b_addr (cmd_b_addr),
.cmd_b_ready (cmd_b_ready),
// Slave Interface Write Response Ports
.S_AXI_BID (S_AXI_BID),
.S_AXI_BRESP (S_AXI_BRESP),
.S_AXI_BUSER (S_AXI_BUSER),
.S_AXI_BVALID (S_AXI_BVALID),
.S_AXI_BREADY (S_AXI_BREADY),
// Master Interface Write Response Ports
.M_AXI_BID (M_AXI_BID),
.M_AXI_BRESP (M_AXI_BRESP),
.M_AXI_BUSER (M_AXI_BUSER),
.M_AXI_BVALID (M_AXI_BVALID),
.M_AXI_BREADY (M_AXI_BREADY),
// Trigger detection
.ERROR_TRIGGER (ERROR_TRIGGER),
.ERROR_TRANSACTION_ID (ERROR_TRANSACTION_ID)
);
/////////////////////////////////////////////////////////////////////////////
// Handle Read Channels (AR/R)
/////////////////////////////////////////////////////////////////////////////
// Read Address Port
assign M_AXI_ARID = S_AXI_ARID;
assign M_AXI_ARADDR = S_AXI_ARADDR;
assign M_AXI_ARLEN = S_AXI_ARLEN;
assign M_AXI_ARSIZE = S_AXI_ARSIZE;
assign M_AXI_ARBURST = S_AXI_ARBURST;
assign M_AXI_ARLOCK = S_AXI_ARLOCK;
assign M_AXI_ARCACHE = S_AXI_ARCACHE;
assign M_AXI_ARPROT = S_AXI_ARPROT;
assign M_AXI_ARUSER = S_AXI_ARUSER;
assign M_AXI_ARVALID = S_AXI_ARVALID;
assign S_AXI_ARREADY = M_AXI_ARREADY;
// Read Data Port
assign S_AXI_RID = M_AXI_RID;
assign S_AXI_RDATA = M_AXI_RDATA;
assign S_AXI_RRESP = M_AXI_RRESP;
assign S_AXI_RLAST = M_AXI_RLAST;
assign S_AXI_RUSER = M_AXI_RUSER;
assign S_AXI_RVALID = M_AXI_RVALID;
assign M_AXI_RREADY = S_AXI_RREADY;
endmodule
`default_nettype wire
|
//-----------------------------------------------------------------------------
//-- (c) Copyright 2010 Xilinx, Inc. All rights reserved.
//--
//-- This file contains confidential and proprietary information
//-- of Xilinx, Inc. and is protected under U.S. and
//-- international copyright and other intellectual property
//-- laws.
//--
//-- DISCLAIMER
//-- This disclaimer is not a license and does not grant any
//-- rights to the materials distributed herewith. Except as
//-- otherwise provided in a valid license issued to you by
//-- Xilinx, and to the maximum extent permitted by applicable
//-- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
//-- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
//-- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
//-- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
//-- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
//-- (2) Xilinx shall not be liable (whether in contract or tort,
//-- including negligence, or under any other theory of
//-- liability) for any loss or damage of any kind or nature
//-- related to, arising under or in connection with these
//-- materials, including for any direct, or any indirect,
//-- special, incidental, or consequential loss or damage
//-- (including loss of data, profits, goodwill, or any type of
//-- loss or damage suffered as a result of any action brought
//-- by a third party) even if such damage or loss was
//-- reasonably foreseeable or Xilinx had been advised of the
//-- possibility of the same.
//--
//-- CRITICAL APPLICATIONS
//-- Xilinx products are not designed or intended to be fail-
//-- safe, or for use in any application requiring fail-safe
//-- performance, such as life-support or safety devices or
//-- systems, Class III medical devices, nuclear facilities,
//-- applications related to the deployment of airbags, or any
//-- other applications that could lead to death, personal
//-- injury, or severe property or environmental damage
//-- (individually and collectively, "Critical
//-- Applications"). Customer assumes the sole risk and
//-- liability of any use of Xilinx products in Critical
//-- Applications, subject only to applicable laws and
//-- regulations governing limitations on product liability.
//--
//-- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
//-- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
//
// Description: ACP Transaction Checker
//
// Check for optimized ACP transactions and flag if they are broken.
//
//
//
// Verilog-standard: Verilog 2001
//--------------------------------------------------------------------------
//
// Structure:
// atc
// aw_atc
// w_atc
// b_atc
//
//--------------------------------------------------------------------------
`timescale 1ps/1ps
`default_nettype none
module processing_system7_v5_5_atc #
(
parameter C_FAMILY = "rtl",
// FPGA Family. Current version: virtex6, spartan6 or later.
parameter integer C_AXI_ID_WIDTH = 4,
// Width of all ID signals on SI and MI side of checker.
// Range: >= 1.
parameter integer C_AXI_ADDR_WIDTH = 32,
// Width of all ADDR signals on SI and MI side of checker.
// Range: 32.
parameter integer C_AXI_DATA_WIDTH = 64,
// Width of all DATA signals on SI and MI side of checker.
// Range: 64.
parameter integer C_AXI_AWUSER_WIDTH = 1,
// Width of AWUSER signals.
// Range: >= 1.
parameter integer C_AXI_ARUSER_WIDTH = 1,
// Width of ARUSER signals.
// Range: >= 1.
parameter integer C_AXI_WUSER_WIDTH = 1,
// Width of WUSER signals.
// Range: >= 1.
parameter integer C_AXI_RUSER_WIDTH = 1,
// Width of RUSER signals.
// Range: >= 1.
parameter integer C_AXI_BUSER_WIDTH = 1
// Width of BUSER signals.
// Range: >= 1.
)
(
// Global Signals
input wire ACLK,
input wire ARESETN,
// Slave Interface Write Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_AWADDR,
input wire [4-1:0] S_AXI_AWLEN,
input wire [3-1:0] S_AXI_AWSIZE,
input wire [2-1:0] S_AXI_AWBURST,
input wire [2-1:0] S_AXI_AWLOCK,
input wire [4-1:0] S_AXI_AWCACHE,
input wire [3-1:0] S_AXI_AWPROT,
input wire [C_AXI_AWUSER_WIDTH-1:0] S_AXI_AWUSER,
input wire S_AXI_AWVALID,
output wire S_AXI_AWREADY,
// Slave Interface Write Data Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_WID,
input wire [C_AXI_DATA_WIDTH-1:0] S_AXI_WDATA,
input wire [C_AXI_DATA_WIDTH/8-1:0] S_AXI_WSTRB,
input wire S_AXI_WLAST,
input wire [C_AXI_WUSER_WIDTH-1:0] S_AXI_WUSER,
input wire S_AXI_WVALID,
output wire S_AXI_WREADY,
// Slave Interface Write Response Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID,
output wire [2-1:0] S_AXI_BRESP,
output wire [C_AXI_BUSER_WIDTH-1:0] S_AXI_BUSER,
output wire S_AXI_BVALID,
input wire S_AXI_BREADY,
// Slave Interface Read Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_ARADDR,
input wire [4-1:0] S_AXI_ARLEN,
input wire [3-1:0] S_AXI_ARSIZE,
input wire [2-1:0] S_AXI_ARBURST,
input wire [2-1:0] S_AXI_ARLOCK,
input wire [4-1:0] S_AXI_ARCACHE,
input wire [3-1:0] S_AXI_ARPROT,
input wire [C_AXI_ARUSER_WIDTH-1:0] S_AXI_ARUSER,
input wire S_AXI_ARVALID,
output wire S_AXI_ARREADY,
// Slave Interface Read Data Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID,
output wire [C_AXI_DATA_WIDTH-1:0] S_AXI_RDATA,
output wire [2-1:0] S_AXI_RRESP,
output wire S_AXI_RLAST,
output wire [C_AXI_RUSER_WIDTH-1:0] S_AXI_RUSER,
output wire S_AXI_RVALID,
input wire S_AXI_RREADY,
// Master Interface Write Address Port
output wire [C_AXI_ID_WIDTH-1:0] M_AXI_AWID,
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_AWADDR,
output wire [4-1:0] M_AXI_AWLEN,
output wire [3-1:0] M_AXI_AWSIZE,
output wire [2-1:0] M_AXI_AWBURST,
output wire [2-1:0] M_AXI_AWLOCK,
output wire [4-1:0] M_AXI_AWCACHE,
output wire [3-1:0] M_AXI_AWPROT,
output wire [C_AXI_AWUSER_WIDTH-1:0] M_AXI_AWUSER,
output wire M_AXI_AWVALID,
input wire M_AXI_AWREADY,
// Master Interface Write Data Ports
output wire [C_AXI_ID_WIDTH-1:0] M_AXI_WID,
output wire [C_AXI_DATA_WIDTH-1:0] M_AXI_WDATA,
output wire [C_AXI_DATA_WIDTH/8-1:0] M_AXI_WSTRB,
output wire M_AXI_WLAST,
output wire [C_AXI_WUSER_WIDTH-1:0] M_AXI_WUSER,
output wire M_AXI_WVALID,
input wire M_AXI_WREADY,
// Master Interface Write Response Ports
input wire [C_AXI_ID_WIDTH-1:0] M_AXI_BID,
input wire [2-1:0] M_AXI_BRESP,
input wire [C_AXI_BUSER_WIDTH-1:0] M_AXI_BUSER,
input wire M_AXI_BVALID,
output wire M_AXI_BREADY,
// Master Interface Read Address Port
output wire [C_AXI_ID_WIDTH-1:0] M_AXI_ARID,
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_ARADDR,
output wire [4-1:0] M_AXI_ARLEN,
output wire [3-1:0] M_AXI_ARSIZE,
output wire [2-1:0] M_AXI_ARBURST,
output wire [2-1:0] M_AXI_ARLOCK,
output wire [4-1:0] M_AXI_ARCACHE,
output wire [3-1:0] M_AXI_ARPROT,
output wire [C_AXI_ARUSER_WIDTH-1:0] M_AXI_ARUSER,
output wire M_AXI_ARVALID,
input wire M_AXI_ARREADY,
// Master Interface Read Data Ports
input wire [C_AXI_ID_WIDTH-1:0] M_AXI_RID,
input wire [C_AXI_DATA_WIDTH-1:0] M_AXI_RDATA,
input wire [2-1:0] M_AXI_RRESP,
input wire M_AXI_RLAST,
input wire [C_AXI_RUSER_WIDTH-1:0] M_AXI_RUSER,
input wire M_AXI_RVALID,
output wire M_AXI_RREADY,
output wire ERROR_TRIGGER,
output wire [C_AXI_ID_WIDTH-1:0] ERROR_TRANSACTION_ID
);
/////////////////////////////////////////////////////////////////////////////
// Functions
/////////////////////////////////////////////////////////////////////////////
/////////////////////////////////////////////////////////////////////////////
// Local params
/////////////////////////////////////////////////////////////////////////////
localparam C_FIFO_DEPTH_LOG = 4;
/////////////////////////////////////////////////////////////////////////////
// Internal signals
/////////////////////////////////////////////////////////////////////////////
// Internal reset.
reg ARESET;
// AW->W command queue signals.
wire cmd_w_valid;
wire cmd_w_check;
wire [C_AXI_ID_WIDTH-1:0] cmd_w_id;
wire cmd_w_ready;
// W->B command queue signals.
wire cmd_b_push;
wire cmd_b_error;
wire [C_AXI_ID_WIDTH-1:0] cmd_b_id;
wire cmd_b_full;
wire [C_FIFO_DEPTH_LOG-1:0] cmd_b_addr;
wire cmd_b_ready;
/////////////////////////////////////////////////////////////////////////////
// Handle Internal Reset
/////////////////////////////////////////////////////////////////////////////
always @ (posedge ACLK) begin
ARESET <= !ARESETN;
end
/////////////////////////////////////////////////////////////////////////////
// Handle Write Channels (AW/W/B)
/////////////////////////////////////////////////////////////////////////////
// Write Address Channel.
processing_system7_v5_5_aw_atc #
(
.C_FAMILY (C_FAMILY),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_AXI_ADDR_WIDTH (C_AXI_ADDR_WIDTH),
.C_AXI_AWUSER_WIDTH (C_AXI_AWUSER_WIDTH),
.C_FIFO_DEPTH_LOG (C_FIFO_DEPTH_LOG)
) write_addr_inst
(
// Global Signals
.ARESET (ARESET),
.ACLK (ACLK),
// Command Interface (Out)
.cmd_w_valid (cmd_w_valid),
.cmd_w_check (cmd_w_check),
.cmd_w_id (cmd_w_id),
.cmd_w_ready (cmd_w_ready),
.cmd_b_addr (cmd_b_addr),
.cmd_b_ready (cmd_b_ready),
// Slave Interface Write Address Ports
.S_AXI_AWID (S_AXI_AWID),
.S_AXI_AWADDR (S_AXI_AWADDR),
.S_AXI_AWLEN (S_AXI_AWLEN),
.S_AXI_AWSIZE (S_AXI_AWSIZE),
.S_AXI_AWBURST (S_AXI_AWBURST),
.S_AXI_AWLOCK (S_AXI_AWLOCK),
.S_AXI_AWCACHE (S_AXI_AWCACHE),
.S_AXI_AWPROT (S_AXI_AWPROT),
.S_AXI_AWUSER (S_AXI_AWUSER),
.S_AXI_AWVALID (S_AXI_AWVALID),
.S_AXI_AWREADY (S_AXI_AWREADY),
// Master Interface Write Address Port
.M_AXI_AWID (M_AXI_AWID),
.M_AXI_AWADDR (M_AXI_AWADDR),
.M_AXI_AWLEN (M_AXI_AWLEN),
.M_AXI_AWSIZE (M_AXI_AWSIZE),
.M_AXI_AWBURST (M_AXI_AWBURST),
.M_AXI_AWLOCK (M_AXI_AWLOCK),
.M_AXI_AWCACHE (M_AXI_AWCACHE),
.M_AXI_AWPROT (M_AXI_AWPROT),
.M_AXI_AWUSER (M_AXI_AWUSER),
.M_AXI_AWVALID (M_AXI_AWVALID),
.M_AXI_AWREADY (M_AXI_AWREADY)
);
// Write Data channel.
processing_system7_v5_5_w_atc #
(
.C_FAMILY (C_FAMILY),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_AXI_DATA_WIDTH (C_AXI_DATA_WIDTH),
.C_AXI_WUSER_WIDTH (C_AXI_WUSER_WIDTH)
) write_data_inst
(
// Global Signals
.ARESET (ARESET),
.ACLK (ACLK),
// Command Interface (In)
.cmd_w_valid (cmd_w_valid),
.cmd_w_check (cmd_w_check),
.cmd_w_id (cmd_w_id),
.cmd_w_ready (cmd_w_ready),
// Command Interface (Out)
.cmd_b_push (cmd_b_push),
.cmd_b_error (cmd_b_error),
.cmd_b_id (cmd_b_id),
.cmd_b_full (cmd_b_full),
// Slave Interface Write Data Ports
.S_AXI_WID (S_AXI_WID),
.S_AXI_WDATA (S_AXI_WDATA),
.S_AXI_WSTRB (S_AXI_WSTRB),
.S_AXI_WLAST (S_AXI_WLAST),
.S_AXI_WUSER (S_AXI_WUSER),
.S_AXI_WVALID (S_AXI_WVALID),
.S_AXI_WREADY (S_AXI_WREADY),
// Master Interface Write Data Ports
.M_AXI_WID (M_AXI_WID),
.M_AXI_WDATA (M_AXI_WDATA),
.M_AXI_WSTRB (M_AXI_WSTRB),
.M_AXI_WLAST (M_AXI_WLAST),
.M_AXI_WUSER (M_AXI_WUSER),
.M_AXI_WVALID (M_AXI_WVALID),
.M_AXI_WREADY (M_AXI_WREADY)
);
// Write Response channel.
processing_system7_v5_5_b_atc #
(
.C_FAMILY (C_FAMILY),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_AXI_BUSER_WIDTH (C_AXI_BUSER_WIDTH),
.C_FIFO_DEPTH_LOG (C_FIFO_DEPTH_LOG)
) write_response_inst
(
// Global Signals
.ARESET (ARESET),
.ACLK (ACLK),
// Command Interface (In)
.cmd_b_push (cmd_b_push),
.cmd_b_error (cmd_b_error),
.cmd_b_id (cmd_b_id),
.cmd_b_full (cmd_b_full),
.cmd_b_addr (cmd_b_addr),
.cmd_b_ready (cmd_b_ready),
// Slave Interface Write Response Ports
.S_AXI_BID (S_AXI_BID),
.S_AXI_BRESP (S_AXI_BRESP),
.S_AXI_BUSER (S_AXI_BUSER),
.S_AXI_BVALID (S_AXI_BVALID),
.S_AXI_BREADY (S_AXI_BREADY),
// Master Interface Write Response Ports
.M_AXI_BID (M_AXI_BID),
.M_AXI_BRESP (M_AXI_BRESP),
.M_AXI_BUSER (M_AXI_BUSER),
.M_AXI_BVALID (M_AXI_BVALID),
.M_AXI_BREADY (M_AXI_BREADY),
// Trigger detection
.ERROR_TRIGGER (ERROR_TRIGGER),
.ERROR_TRANSACTION_ID (ERROR_TRANSACTION_ID)
);
/////////////////////////////////////////////////////////////////////////////
// Handle Read Channels (AR/R)
/////////////////////////////////////////////////////////////////////////////
// Read Address Port
assign M_AXI_ARID = S_AXI_ARID;
assign M_AXI_ARADDR = S_AXI_ARADDR;
assign M_AXI_ARLEN = S_AXI_ARLEN;
assign M_AXI_ARSIZE = S_AXI_ARSIZE;
assign M_AXI_ARBURST = S_AXI_ARBURST;
assign M_AXI_ARLOCK = S_AXI_ARLOCK;
assign M_AXI_ARCACHE = S_AXI_ARCACHE;
assign M_AXI_ARPROT = S_AXI_ARPROT;
assign M_AXI_ARUSER = S_AXI_ARUSER;
assign M_AXI_ARVALID = S_AXI_ARVALID;
assign S_AXI_ARREADY = M_AXI_ARREADY;
// Read Data Port
assign S_AXI_RID = M_AXI_RID;
assign S_AXI_RDATA = M_AXI_RDATA;
assign S_AXI_RRESP = M_AXI_RRESP;
assign S_AXI_RLAST = M_AXI_RLAST;
assign S_AXI_RUSER = M_AXI_RUSER;
assign S_AXI_RVALID = M_AXI_RVALID;
assign M_AXI_RREADY = S_AXI_RREADY;
endmodule
`default_nettype wire
|
End of preview. Expand
in Dataset Viewer.
pipeline_tag: text-generation tags:
- code model-index:
- name: VeriGen
results:
- task: type: text-generation dataset: type: name:
extra_gated_prompt: >-
Model License Agreement
Please read the BigCode OpenRAIL-M
license
agreement before accepting it.
extra_gated_fields:
I accept the above license agreement, and will use the Model complying with the set of use restrictions and sharing requirements: checkbox
VeriGen
Dataset Summary
The dataset comprises Verilog modules as entries. The entries were retrieved from the GitHub dataset on BigQuery.
For training [models (https://huggingface.co./shailja/fine-tuned-codegen-2B-Verilog)], we filtered entries with no of characters exceeding 20000 and duplicates (exact duplicates ignoring whitespaces).
Paper: Benchmarking Large Language Models for Automated Verilog RTL Code Generation
Point of Contact: contact@shailja
Languages: Verilog (Hardware Description Language)
Data Splits
The dataset only contains a train split.
Use
# pip install datasets
from datasets import load_dataset
ds = load_dataset("shailja/Verilog_GitHub", streaming=True, split="train")
print(next(iter(ds)))
#OUTPUT:
Intended Use
The dataset consists of source code from a range of GitHub repositories. As such, they can potentially include non-compilable, low-quality, and vulnerable code.
Attribution & Other Requirements
The pretraining dataset of the model was not filtered for permissive licenses only. Nevertheless, the model can generate source code verbatim from the dataset. The code's license might require attribution and/or other specific requirements that must be respected.
License
The dataset is licensed under the BigCode OpenRAIL-M v1 license agreement. You can find the full agreement here.
Citation
@misc{https://doi.org/10.48550/arxiv.2212.11140,
doi = {10.48550/ARXIV.2212.11140},
url = {https://arxiv.org/abs/2212.11140},
author = {Thakur, Shailja and Ahmad, Baleegh and Fan, Zhenxing and Pearce, Hammond and Tan, Benjamin and Karri, Ramesh and Dolan-Gavitt, Brendan and Garg, Siddharth},
title = {Benchmarking Large Language Models for Automated Verilog RTL Code Generation},
publisher = {arXiv},
year = {2022},
copyright = {arXiv.org perpetual, non-exclusive license}
}
- Downloads last month
- 198
Size of downloaded dataset files:
1.89 GB
Size of the auto-converted Parquet files:
432 MB
Number of rows:
108,971
